Avery Dennison SNAP 700 Скачать руководство пользователя страница 13

Страница: 13 / 153

User’s Manual—SNAP™ 700 Printer

2.3 Unpacking

2.3.1 Removing the printer from the carton

1. Open the carton from the top by removing the banding straps and/or cutting

the taped seam on the top of the carton.

2. Remove top foam-packing layer (see Figure 2A).

Figure 2A – Shipping Carton

CAUTION: Do not discard any of the packing / shipping
material in case you have to move the printer to another
location or return it to AVERY DENNISON for service.

3. The printer has been wrapped with shrink wrap to protect the printer from the

packing material and moisture.

4. It requires 2 people to remove the printer from the carton.

5. Position your hands in the cardboard cutout as above. Carefully lift it out of

the box. Lift the printer from the bottom out of the lower foam packing and
place the printer on the workstation table.

6. Carefully remove the shrink wrap to avoid damaging the printer.

7. Turn the Stock Arbor knob counter-clockwise and remove the protective foam

behind the Stock Arbor.

8. Unpack the stacker from its box and place it on the workstation table next to

the printer. Refer to Section 2.5.1, Attaching the Stacker.

CAUTION: Lifting the printer from any component other
than case or stacker supports can damage the printer and
cause needless start up delays.

Содержание SNAP 700

























































































































































Результаты поиска

Содержание SNAP 700

Отзывы:

Похожие инструкции для SNAP 700

Бренды по названию

Популярные бренды

Avery Dennison SNAP 700, Руководство оператора и по обслуживанию

Результаты поиска

Содержание SNAP 700

Отзывы:

Похожие инструкции для SNAP 700

Бренды по названию

Популярные бренды