Avery Dennison SNAP 700 Скачать руководство пользователя страница 112

Страница: 112 / 153

112

User’s Manual—SNAP™ 700 Printer

8. Option Menu System Flowchart

PRESS AND HOLD VOICE
BUTTON UNTIL OPTION
MENU BEGINS

PRESS START FOR TEST
PATTERNS

PRESS START FOR
DEMOS

PRESS START TO SET
VOLUME

RETURNING TO PRINT MODE.

PRESS START FOR
PRINT SETUP TEST
PATTERN

PRESS START FOR
SAMPLE LABEL TEST
PATTERN

PRESS START FOR
CUSTOM TEST
PATTERN 1

PRESS START FOR
CUSTOM TEST
PATTERN 2

READY TO PRINT
SETUP TEST PATTERN.
RETURNING TO PRINT
MODE.

LOADS PRINT SETUP
TEST PATTERN AND
RETURNS TO PRINT
MODE.

READY TO PRINT SAMPLE
LABEL TEST PATTERN.
RETURNING TO PRINT
MODE

LOADS SAMPLE LABEL
TEST PATTERN AND
RETURNS TO PRINT
MODE.

READY TO PRINT CUSTOM
TEST PATTERN 1.
RETURNING TO PRINT
MODE.

LOADS CUSTOM TEST
PATTERN 1 AND RETURNS
TO PRINT MODE.

READY TO PRINT CUSTOM
TEST PATTERN 2.
RETURNING TO PRINT
MODE

LOADS CUSTOM TEST

PRESS START FOR SHORT
DEMO

PLAYS SHORT DEMO AND
RETURNS TO PRINT MODE.

PRESS START FOR LONG DEMO.

PLAYS LONG DEMO

-PRESS START TO PLAY NEXT SECTION.
-PRESS VOICE TO REPEAT LAST SECTION.
-PRESS AND HOLD VOICE TO EXIT TO PRINT MODE.

RETURNS TO PRINT MODE AFTER LAST SECTION

PRESS START TO EXIT

RETURNING TO PRINT
MODE.RETURNS TO PRINT
MODE

PRESS START
FOR VOLUME
LEVEL 3

SETTING VOLUME TO
LEVEL 3. RETURNING TO
PRINT MODE

SETS VOLUME TO LEVEL
3 AND RETURNS TO
PRINT MODE

PRESS START
FOR VOLUME
LEVEL 4

SETTING VOLUME TO
LEVEL 4. RETURNING
TO PRINT MODE.
SETS VOLUME TO
LEVEL 4 AND RETURNS
TO PRINT MODE.

PRESS START
FOR VOLUME
LEVEL 5

SETTING VOLUME TO
LEVEL 5. RETURNING TO
PRINT MODE.
SETS VOLUME TO LEVEL
5 AND RETURNS TO
PRINT MODE.

PRESS START
TO EXIT

PRESS START
FOR VOLUME
LEVEL 1

SETTING VOLUME TO
LEVEL 1. RETURNING TO
PRINT MODE.
SETS VOLUME TO LEVEL
1 AND RETURNS TO
PRINT MODE

PRESS START
FOR VOLUME
LEVEL 2

SETTING VOLUME TO
LEVEL 2. RETURNING
TO PRINT MODE.
SETS VOLUME TO
LEVEL 2 AND RETURNS
TO PRINT MODE.

RETURNING TO
PRINT MODE.

RETURNS TO
PRINT MODE.

PRESS START TO EXIT

RETURNING TO PRINT
MODE

RETURNS TO PRINT MODE

VOICE OPTION MENU NAVIGATION CHART

PRESS VOICE BUTTON TO GO TO THE NEXT OPTION

PRESS START BUTTON TO ACCEPT THE CURRENT OPTION

NOTE: PRESS AND HOLD THE VOICE BUTTON AT ANY TIME TO EXIT THE VOICE MENU SYSTEM.

Содержание SNAP 700

























































































































































Результаты поиска

Содержание SNAP 700

Отзывы:

Похожие инструкции для SNAP 700

Бренды по названию

Популярные бренды

Avery Dennison SNAP 700, Руководство оператора и по обслуживанию

Результаты поиска

Содержание SNAP 700

Отзывы:

Похожие инструкции для SNAP 700

Бренды по названию

Популярные бренды