Avery Berkel A301CE Скачать руководство пользователя страница 99

Страница: 99 / 168

7 — Appendices

Service Instructions RP-A301CE/RP-A351CE/RP-A355CE

7 - 25

Set up menu

To enter the

MAIN MENU

when the

programmable portioner is off, press the

ESC

button.

The

Language

message, will be visualised.

To select the functions in a cyclic way press the

MANUAL

and

AUTOMATIC

buttons.

After programming, press the

ESC

button for a

few seconds to go back to the normal working.

Language

This function allows to change the language of
the different messages.

Pressing the

ENT

button it is possible to enter the

language selection.

Pressing the

MANUAL

button the writings

ltaliano, English, Deutsch, Francais, Espanol will
be visualised on the display one after the other.

To confirm the set up language, press the

ENT

button, e.g. if the chosen language is French the

Langue

message will be visualised.

Cutting Pause

The cutting pause function delays the cutting of
the following slice of product; in this way it is
easier to put the slice on the proper slice
receiving tray.

25 tenth of a second is the max. programmable
time.

Press the

ENT

button to visualise the

Cutting

Pause

message; use the numeric buttons to set

up the datum and press

ENT

to confirm.

Содержание A301CE









































































































































































Результаты поиска

Содержание A301CE

Отзывы:

Avery Berkel A301CE, Инструкция по эксплуатации, Страница: 99 / 168

Результаты поиска

Содержание A301CE

Отзывы: