Avery Berkel A301CE Скачать руководство пользователя страница 100

Страница: 100 / 168

7 — Appendices

7 - 26

Service Instructions RP-A301CE/RP-A351CE/RP-A355CE

Auto Power Off

Auto power off: if the machine is not used for a time
which is longer than the fixed one, it stops
automatically.

99 minutes is the max. programmable time.

Press the

ENT

button to visualise the

Auto Power

Off

message; use the numeric buttons to set up

the datum and press

ENT

confirm.

Blade Rotation Off

Blade Rotation off: if the product holder is not used
for a time which is longer than the fixed one, the
machine stops automatically

99 seconds is the max programmable time.

Press the

ENT

button to visualise the

Blade Rotat.

Off

message; use the numeric buttons to set up

the datum and press

ENT

to confirm.

Beep Activation

Beep Activation: the buzzer sound on
(value =1) / off (value=0).

Press the

ENT

button to visualise the

Beep Enable

message; set up the datum and press

ENT

confirm.

Feed Carriage Delay

Feed carriage delay: it is the time between the
blade starting and the product holder starting. This
allows the blade to achieve the right revolution
number before cutting.

Press the

ENT

button to visualise the

Carriage

Delay

message; use the numeric buttons to set up

the datum (max. 25) and press

ENT

to confirm.

Содержание A301CE









































































































































































Результаты поиска

Содержание A301CE

Отзывы:

Avery Berkel A301CE, Инструкция по эксплуатации, Страница: 100 / 168

Результаты поиска

Содержание A301CE

Отзывы: