manualshive.com logo in svg

Avery Berkel A301CE, Инструкция по эксплуатации, Страница: 95 / 168

Поделиться
Скачать
Avery Berkel A301CE Скачать руководство пользователя страница 95

7 —  Appendices

Service Instructions RP-A301CE/RP-A351CE/RP-A355CE

7 - 21

Slice function

Press the 

ENT

 button to visualise the 

Slicers:

message.

Press the 

ESC

 button to reset the slice number.

Use the numerical buttons to set up the desired
slice number, press the 

ENT

 button to confirm the

datum.

Set up the product holder travel.

Press the 

AUTOMATIC

 button to start both the

blade and the product holder (led L3 on).

When the machine gets to the fixed slice number,
it stops automatically.

If the slice number is zero, pressing the

AUTOMATIC

 button the machine does not work

and the 

Attention

 message is visualised on the

display.

Weight function

Press the 

ENT

 button to visualise the 

Weight:

message.

Press the 

ESC

 button to reset the weight already

set up.

Use the numerical buttons to set up the desired
slice number; press the 

ENT

 button to confirm

the datum.

Set up the product holder travel.

Press the 

AUTOMATIC

 button to start both the

blade and the product holder (led L3 on).

When the machine gets to the fixed weight, it
stops automatically.

If the weight is zero, pressing the 

AUTOMATIC

button the machine does not work and the

Attention

 message is visualised on the display.

Machine stopping

Pressing the 

O

 button the machine stops; the

product holder finishes its working cycle and
stops to the end near the operator.

Содержание A301CE









































































































































































Отзывы:

Нет отзывов