manualshive.com logo in svg

Avery Berkel A301CE, Инструкция по эксплуатации, Страница: 102 / 168

Поделиться
Скачать
Avery Berkel A301CE Скачать руководство пользователя страница 102

7 —  Appendices

7 - 28

Service Instructions RP-A301CE/RP-A351CE/RP-A355CE

Sample Weight

Sample weight: it is the reference sample weight
(gr) to calibrate the weighing system.

Press the 

ENT

 button to visualise the 

Weight

Sample

 message; use the numeric buttons to set

up the datum (max. 4000 gr) and press 

ENT

 to

confirm.

Cell Calibration

Cell calibration: it allows to calibrate the loading cell
and the converter A/D automatically.

Before carrying on the calibration, make sure that
the weight sample value has already been set up in
the sample weight function, otherwise it is
impossible to go on calibrating.

Put the empty slice receiving tray on the loading
cell press the and follow the calibration instructions
which appear in progression on the display.

1.

Wait until the reading has steadied.

2.

Press the 

0

 button to obtain Zero.

3.

Place the sample weight on the slice
receiving tray and wait until the reading has
steadied.

4.

Press the 

0 

button to obtain the sample

weight.

Finished calibrating the 

Cell Calibration

 message

will be visualised automatically.

Содержание A301CE









































































































































































Отзывы:

Нет отзывов