Avery Berkel A301CE Скачать руководство пользователя страница 37

Страница: 37 / 168

3 — Operation

Service Instructions RP-A301CE/RP-A351CE/RP-A355CE

3 - 23

3.1.8

Blade sharpening A351CE

If the cut is not adequate, the blade must be
sharpened. The intervals between the
sharpening operations depend on the use of
the slicer and the kind of products being cut.

This operation must only be carried out by
qualified personnel.

The blade must be replaced when its
diameter is 10 mm less than when original
(see 3.1.3).

WARNING:

REPLACEMENT OF THE BLADE IS
A DANGEROUS OPERATION.

IF THE CUT IS INADEQUATE
AFTER SHARPENING, REPLACE
THE STONES. CONTACT
AVERY BERKEL FOR
ASSISTANCE.

Sharpening operation

Note:

Sharpening must be performed during
manual operation.

WARNING:

WEAR PROTECTIVE GLOVES.

For correct sharpening of the blade follow
these instructions:

Clean the blade to remove any greasy
residue, as in 3.1.6.

Make sure that the machine is off.

Содержание A301CE









































































































































































Результаты поиска

Содержание A301CE

Отзывы:

Avery Berkel A301CE, Инструкция по эксплуатации, Страница: 37 / 168

Результаты поиска

Содержание A301CE

Отзывы: