Avery Berkel A301CE Скачать руководство пользователя страница 83

Страница: 83 / 168

7 — Appendices

Service Instructions RP-A301CE/RP-A351CE/RP-A355CE

7 - 9

Control of the functions

The control is effected by sliding the DIP SWITCH no. 15 to position ON

Illuminated
indicator
no.

Description of the function

Mains power applied to the board.

Blade cover microswitch if fitted on the machine.

Blade cover microswitch and sharpener microswitch when both of them are
fitted on the machine

Blade motor start pushbutton.

Blade motor stop pushbutton.

Proximity microswitch on the handle “MANUAL-AUTOMATIC”; it can be
checked only with the blade motor on.

Carriage motor stop pushbutton; it can be checked only with the blade motor
on.

Carriage motor start pushbutton; it can be only checked with the blade motor
on.

Carriage end stroke on the blade

Carriage end stroke on the operator side.

11A Board electronic side; it illuminates when the blade and carriage motor are

working.

11B Board electronic side when the carriage returns towards the operator; it

illuminates when the blade and carriage motor are working.

Components

Integrated MOC 3040

14A Fuse:

160mA tension 220/50Hz
200mA tension 110V/50Hz

14B Fuse:

500mA
800mA for the Slice counter

Switch

Transformer

Relay

Trimmer to adjust the carriage stroke

Содержание A301CE









































































































































































Результаты поиска

Содержание A301CE

Отзывы:

Avery Berkel A301CE, Инструкция по эксплуатации, Страница: 83 / 168

Результаты поиска

Содержание A301CE

Отзывы: