manualshive.com logo in svg

Avaya 1408, Руководство по установке

Поделиться
Скачать
Avaya 1408 Скачать руководство пользователя страница 144

PARTNER Version Installation Manual

Page 144

- Issue 1c (09 April 2010)

IP Office Essential Edition

Performance figures and data quoted in this document are typical, and must be

specifically confirmed in writing by Avaya before they become applicable to any

particular order or contract. The company reserves the right to make alterations

or amendments to the detailed specifications at its discretion. The publication of

information in this document does not imply freedom from patent or other

protective rights of Avaya or others.

All trademarks identified by the ® or ™ are registered trademarks or trademarks,

respectively, of Avaya Inc. All other trademarks are the property of their

respective owners.

This document contains proprietary information of Avaya and is not to be

disclosed or used except in accordance with applicable agreements.

© 2010 Avaya Inc. All rights reserved.

Содержание 1408

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды