manualshive.com logo in svg

Autostart AS-6010 TW-A, Руководство по установке, Страница: 9 / 22

Поделиться
Скачать
Autostart AS-6010 TW-A Скачать руководство пользователя страница 9

Installation Guide   

P. 9

 

Pin Switch too many times, you will enter 

Diagnostic Mode 

rather than Programming Mode.  

5.

 

You now have 20 seconds to select one of the sub-

menus. 

 

 

Table 1: Flashing the Hood Pin switch 

Once the System has entered Programming Mode, you will have a selection of many different sub-
menus, which will be described later in this Guide: 

a.  Transmitter Programming 
b.  Programming Options 
c.  Honk/Horn Timing (if available) 
d.  Tach Programming 

Remember: 

Once the Parking Lights are 

ON

 (solid), you have up to 20 seconds to select a sub-menu. If you 

do not select a sub-menu within 20 seconds, the System will exit Programming Mode and you will 
have to flash the Hood Pin switch once again. 

The Programming Assistance Button 

(A.k.a. the 

PAB

.) Mounted on the System, this 

button can be used from within the vehicle 

instead of the Hood Pin switch in the Engine 
compartment. This will spare the installer the 
trouble of accessing the Hood Pin switch in the 
Engine compartment.

  

 

Caution 

The Hood Pin switch must be installed and  connec ted in order for the Programming 
Assistance Button to function. 

The button will work only when the Hood is up.

 

Programming a Transmitter 

Before you Proceed 

The Transmitter of the System is not delivered pre-programmed: it must be programmed after the 
wiring of the System is completed. The System has the ability to retain up to 4 different Transmitter 

codes; if a fifth Transmitter is  programmed, the code of the first Transmitter will be lost from 
memory. 

To erase all Transmitter codes from memory,  you must perform a reset of the 

System

 (see 

Resetting the System

, later in this Guide, for more details). 

A Word of Caution About the Alarm 

The Alarm is triggered when the Unit is powered up because the default state of the Alarm is 

ARMED

.  You will therefore need to shut off the Alarm before you carry out the Transmitter 

Programming procedure. 

One way to shut off the Alarm is to (1) set the System to Valet Mode and then (2) immediately set 
the System 

out of

 Valet Mode. (See instructions below.) 

Getting into Valet Mode 

Содержание AS-6010 TW-A























Отзывы:

Нет отзывов