background image

Installation Guide   

P. 17

 

Smart Secure Lock 

If the vehicle is initially locked, upon remote 

START

 the System will trigger an 

unlock pulse 

and a 

disarm pulse 

before the Engine is started. The System will 

LOCK

 again when the Engine is 

running, and 

LOCK

 once again 4 seconds after shut-down. 

If the vehicle is initially 

unlocked

, upon remote 

START

 the System will start the Engine and arm the 

Starter Kill and Alarm, but the Doors will not be locked or unlocked at any moment of the 

sequence. 

Lock Pulse Duration 

The duration of the Lock and Unlock pulses can be configured as follows: 

 

(Default) 7/10-sec. 

LOCK

 and 7/10-sec. 

UNLOCK

 pulses 

 

4-sec. 

LOCK/UNLOCK

 

pulses  to control vacuum Door Lock systems 

 

single 7/10-sec. 

LOCK

 pulse and

 two 1/4-sec.

 

UNLOCK

 pulses 

 for double-pulse disarm/unlock systems. 

 

1/10-sec. 

LOCK

 and 1/10-sec. 

UNLOCK

 pulses 

Engine Run Time 

Use this Function to configure the length of time the Engine will be left running under remote 

control. The System will allow the Engine to run for either 

4, 15 or 25

 min. in Gas Mode and 

9, 20 

or 30

 min. in Diesel Mode. Standard default Run Time is 15 minutes in Gas mode and 20 minutes 

in Diesel mode. 

Open Zone Notification 

This feature will warn the user when a Door is left open: upon the arming of the System, a 10-sec. 
notification delay will take place, after which the Siren will chirp 3 times if an open door is detected. 

Starter Kill (Installation) 

The System is equipped with a selectable 

Passive 

or 

Active-arming Starter Kill 

circuit that will 

prevent the vehicle from being started with the Ignition Key when the System is armed. The Starter 
Kill wire will provide a constant 500-mA. negative output when the system is 

armed 

(locked by 

remote control) and can be connected to an external Starter or Ignition interrupt relay.  
The Starter Kill circuit follows the arming function of the Alarm and therefore can be set to arm in 

either 

Passive Mode

 or 

Active Mode

Passive or Active Arming 

 

Active Arming

: the Alarm and the Starter Kill will 

not 

arm automatically. Press the 

LOCK

 button to arm and the 

UNLOCK

 button to disarm it. 

 

Passive Arming: 

the Alarm and the Starter Kill will arm automatically if it is not armed 

by remote within a 30-sec. delay. Press 

UNLOCK

 to disarm. 

 

Passive Arming 

without Siren Mute. Press 

UNLOCK

 to disarm. 

 

Disarmed Notification:

 See description below. 

Disarmed Notification 

This feature will notify the user when the vehicle is left disarmed: (1) after Ignition is turned 

off

 and 

the Ignition Key is removed from the Ignition Switch, or (2) when the System is disarmed after 
being previously armed, the opening or closing of a Door will start a 10-sec. timer, after which the 
Horn or Siren will 

chirp once

, if the vehicle was left unprotected, to warn the user. Pressing 

LOCK

 

or 

UNLOCK

 before the 10-sec. delay elapses will cancel this warning. 

Содержание AS-6010 TW-A























Отзывы: