Autostart AS-6010 TW-A Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 22

Autostart AS-6010 TW-A Скачать руководство пользователя страница 16

P. 16

Installation Guide

Supplementary Information

Fifth Relay Output (2

nd

IGN, ACC or CRANK)

Systems of this series are equipped with an

on-board high-current programmable 5

th

Relay that can be used to power a second
Ignition, Accessory or Crank wire.
The Unit uses 3 sets of pins; each set
corresponds to a specific function of the

output. In order to activate one of the three
possible functions, you must place the
Jumper (supplied) on one of the three sets
of pins and connect the 14 AWG wire to the

second

IGN. / ACC. / CRANK

wire of the

vehicle.

Caution!

Only one set of pins can be used at one time.

Using more than one Jumper may result in

serious damage to the vehicle.
The relay output rating on this unit is 25 A at most. Defective OEM solenoid switches can

sometimes draw up to 50 or 60 A, causing the 30 A Fuse to blow. Always verify your circuit
with an appropriate measuring device.

Ignition-controlled Door Locks

This feature will

LOCK

all the Doors of the vehicle when the Brake Pedal is pressed while the

Ignition Key is in the

IGNITION ON (RUN)

position. The unit will

UNLOCK

all Doors when the Ignition Key

is turned back to the

OFF

position.

If

Ignition Lock Only

is selected, the system will only

LOCK

all Doors when the Brake Pedal is

pressed while the Ignition Key is in the

IGNITION ON (RUN)

position.

If option

Ignition Unlock Only

is selected, the system will

UNLOCK

all Doors when the key is turned

to the

OFF

position (provided that the Ignition key was in the

IGNITION ON (RUN)

position and that the

Brake Pedal was pressed at least once).

Ignition Re-lock

This feature is automatically available whenever

Ignition Lock

is available. When Ignition is

ON

(but not under remote start) and a Door is opened and closed, the system will re-lock all doors next
time the Brake Pedal is pressed.

Secure Lock

This feature allows the System to control certain OEM factory Alarm systems without requiring the
use of other wires for disarming the OEM Alarm. (Namely, this feature is designed for OEM
systems which use the factory Lock wire to

arm

the Alarm and the Unlock wire to

disarm

it.)

Standard Secure Lock

If this Option is selected, upon receiving a remote

START

signal, Secure Lock will

UNLOCK

the Doors

(disarming the factory Alarm); 1/2 sec. after remote start Secure Lock will

re-lock

the Doors. 4

seconds after shutdown, Secure Lock will

re-lock

all Doors (

arming

the system once again).

Please note

that most OEM systems will

not

rearm the Alarm while the Engine is running, but

will

still lock the Doors.

«
...
14
15
16
17
18
...
»

Содержание AS-6010 TW-A























Отзывы:

Нет отзывов