AutomationDirect IronHorse GSDA-DP-S Скачать руководство пользователя страница 6

Страница: 6 / 16

Page 6

IronHorse GSDA-DP-S User Manual – 1st Edition – 09/18/2019

GSDA-DP-S i

nStAllAtion

nstallatiOn

GsDa-DP-s

PANEL MOUNTING GASKET

(WITH THE ADHESIVE SIDE OF

GASKET FACING THE CUSTOMER

MOUNTING PANEL)

CUSTOMER

MOUNTING PANEL

(HOLE CUT-OUT FOR CONTROL

HOUSING APPROXIMATELY

3.622" WIDE BY 1.770" HIGH)

GSDA-DP-S

CONTROL

SUPPLIED WITH EACH CONTROL:

1) GASKET

2) (2) 6-32 X 3/4 PANHEAD BLACK OXIDE STAINLESS SCREWS

3) (2) #6 NUT WITH LOCKWASHER

Exploded Panel View

OUt

anD

OUntinG

iMensiOns

HOUSING DEPTH

4.625 [117.5]

PANEL CUT-OUT

GSDA-DP-S

x 2

GEN

SCL

SPL

ENTER

SIGNAL SCALER

AND GENERATOR

4.00

[101.6]

3.62

[91.9]

0.885 [22.5]

1.77 [45.0]

.140

[3.6]

4.00

[101.6]

5.00

[127.0]

4.625

[117.5]

2.289
[58.1]

1.656
[42.1]

Содержание IronHorse GSDA-DP-S

















Результаты поиска

Содержание IronHorse GSDA-DP-S

Отзывы:

Похожие инструкции для IronHorse GSDA-DP-S

Бренды по названию

Популярные бренды

AutomationDirect IronHorse GSDA-DP-S, Руководство пользователя

Результаты поиска

Содержание IronHorse GSDA-DP-S

Отзывы:

Похожие инструкции для IronHorse GSDA-DP-S

Бренды по названию

Популярные бренды