Automation Direct D0-DEVNETS Скачать руководство пользователя страница 19

Страница: 19 / 78

Installation and

Safety Guidelines

Installing the DeviceNet

Slave Module

2–8

Installing the D0–DEVNETS Slave Module

D0–DEVNETS DeviceNet Slave
Module User Manual, Rev A

STATUS

The adapter has two Status Indicators,
one for

odule

tatus and the other for

etwork

tatus.

MS (Module Status) Indicator

Indication

Status

OFF

No power to module.

Solid Green

Power is ON, normal condition

Solid Red

Critical module Failure

NS (Network Status) Indicator

Indication

Status

OFF

No power to module or no Network Access

Flashing Green

Online but not connected (no connection
established)

Solid Green

Online, link okay and connected

Flashing Red

Recoverable fault

Solid Red

Critical module Failure (Duplicate ID or Bus off)

Status Indicators

Содержание D0-DEVNETS















































































Результаты поиска

Содержание D0-DEVNETS

Отзывы:

Похожие инструкции для D0-DEVNETS

Бренды по названию

Популярные бренды

Automation Direct D0-DEVNETS, Руководство пользователя

Результаты поиска

Содержание D0-DEVNETS

Отзывы:

Похожие инструкции для D0-DEVNETS

Бренды по названию

Популярные бренды