Automatic Technology Syncro ATS-3 Скачать руководство пользователя страница 9

Страница: 9 / 26

ATS Series Installation Manual

11. Specifications

Technical Specifications

SYNCRO

ATS-3

TEMPO

ATS-2

Rated voltage range:

230V - 240Va.c.

Rated frequency:

50Hz / 60Hz

Rated power input:

165W

Door opening:

Maximum Door Area:

Maximum Door Weight:

Door must be well balanced and able to

be operated by hand, as per warranty

conditions and AS/NZS 4505:2012

18m

236kg*

18m

200kg*

Minimum headroom

57mm

Rated Operating Time

4 mins

Rated Temp

C to +40

Short Term Peak force:

1100N

Rated load

400N

Nominal force

200N (20kg)

Receiver type

Multi-frequency UHF FM

(433.47, 433.92 & 434.37MHz)

Multi-frequency UHF FM

(433.47, 433.92 & 434.37MHz)

Receiver code storage capacity

64 X 4-button Transmitters

Transmitter battery

CR2032 (3 Volts)

Main light

LED (Light Emitting Diodes)

Network connectivity

Network ready,

Smart hub already installed

Network compatible,

(requires optional Smart Phone Control Kit)

* Gross door weight, including all fittings

Note: Intermittent operations may occur in areas which experience very strong winds. The strong wind puts extra pressure on the

door and tracks which may in turn intermittently trigger the safety obstruction detection system.

Содержание Syncro ATS-3



























Результаты поиска

Содержание Syncro ATS-3

Отзывы:

Похожие инструкции для Syncro ATS-3

Бренды по названию

Популярные бренды

Automatic Technology Syncro ATS-3, Руководство пользователя

Результаты поиска

Содержание Syncro ATS-3

Отзывы:

Похожие инструкции для Syncro ATS-3

Бренды по названию

Популярные бренды