Automatic Technology Syncro ATS-3 Скачать руководство пользователя страница 24

Страница: 24 / 26

ATS Series Installation Manual

Parameter

Value options = Indicated by brightness

of main light

(DEFAULT parameter underlined)

Name

Flashes

MARGIN*

1.0A

1.2A

1.4A

1.6A

2.0A

PE AUTO-CLOSE

OFF

15sec

30sec

60sec

90sec

AUTO-CLOSE

OFF

15sec

30sec

60sec

90sec

120sec

LIGHT TIMER

30sec

60sec

90sec

120sec

180sec

240sec

B - Adjustment Mode Instructions

a. Press the MODE button repetitively until the GEAR

LED starts flashing

b. Referring to the table below, select the desired parameter using the OPEN

and CLOSE

buttons and observing the

number of flashes on the GEAR

LED. The selected parameter’s value is indicated by the main light’s brightness.

c. Press STOP / SET button to start editing the parameter’s value. The TRANSMIT

LED will turn on when editing is active.

d. Use the OPEN

and CLOSE

buttons to step through the available options. The light’s brightness will change

accordingly.

Adjusting Safety Obstruction Force

The Safety Obstruction Force is calculated automatically during

setup. Adjusting this is normally only necessitated by environmental

conditions such as windy or dusty areas, and areas with extreme

temperature changes.

To Increase / Decrease Force Pressure

a. Press the MODE button repetitively until the GEAR

LED is

flashing.

b. The LED will start flashing with one flash every second.

c. Press the STOP / STEP button and the MODE button LED and the

TRANSMIT

LED will be lit and the GEAR

LED will flash

once every second.

d. By pressing the OPEN button

will increase the force pressure

and CLOSE button

will decrease the force - Main light will dim

or brighten as the pressure is decreased or increased.

e. Press STOP / SET button to save the new value. (Refer to

Appendix B for margin settings)

f. Test the force again as per Testing Close Cycle and Testing Open

Cycle.

C - Adjusting Force Margins

* only available with firmware 55 onward

Pressing the MODE button when a parameter is

being adjusted will load the default value.

tip

e. Press STOP / SET button to save the parameter’s new value or press MODE to leave the value unchanged.

f. Continue from a. above to select another parameter or press MODE to exit adjustment mode.

When parameter edit mode

is active, if any button other

than MODE is pressed, then

when MODE is pressed

again, operating mode will

be selected instead of the

NETWORK adjustment mode.

tip

Содержание Syncro ATS-3



























Результаты поиска

Содержание Syncro ATS-3

Отзывы:

Похожие инструкции для Syncro ATS-3

Бренды по названию

Популярные бренды

Automatic Technology Syncro ATS-3, Руководство пользователя

Результаты поиска

Содержание Syncro ATS-3

Отзывы:

Похожие инструкции для Syncro ATS-3

Бренды по названию

Популярные бренды