Automatic Technology PA1000V1 страница 5 Скачать руководство пользователя

Страница: 5 / 38

Safety Rules

(

Les règles de la sécurité

)

Please read these important safety rules

These safety alert symbols indicate a personal safety or property damage

instruction exists. READ ThESE INSTRuCTIoNS CAREfuLLy.

This automatic garage door operator is designed and tested to offer safe service

provided it is installed and operated in strict accordance with the following

safety rules. failure to comply with the installation instructions and the safety

warnings may result in death, serious personal injury and/or property damage.

CAuTIoN:

If your garage has no pedestrian entrance

door, an emergency access device should be installed.

This accessory allows manual operation of the garage

door from outside in case of power failure.

Position the Garage Door Operator so that the power plug

is accessible when inserted into the power outlet.

This opener should be installed in accordance with relevant

US and Canada Standards.

Do not allow children to play with door controls.

Keep transmitters away from children.

Watch the moving door and keep people away until the

door is completely opened or closed.

Activate the operator only when the garage door is in full

view, free of obstructions and with the opener properly

adjusted.

Keep the garage door balanced. Sticking or binding doors

must be repaired. Garage doors, door springs, brackets

and their hardware are under extreme tension and can

cause serious personal injury. Do not attempt any garage door
adjustment. Do not use if repair or adjustment is needed. Call
for professional garage door service.

Install the wall transmitter in a location where the garage

door is visible, but out of the reach of children at a height

of at least 5 feet (1.53m).

Disconnect electric power to the garage door operator

before removing covers.

Door must have Safety Beams fitted.

Do not wear rings, watches or loose clothing while

installing or servicing a garage door operator.

This operator is not suitable for commercial, industrial

or common entry applications.

To avoid serious personal injury from entanglement,

remove all unnecessary ropes or chains and disable

any equipment such as locks which are not needed

for powered operation.

Installation and wiring must be in compliance with

your local building and electrical codes. Connect

the power cord only to properly earthed mains. If

an extension lead must be used, make sure it is a 3-core
lead and approved to 7 amp capacity.

To reduce the risk of electric shock, this equipment

has a earthing type plug that has a third (earthing)

pin. This plug will only fit into a earthing type outlet.

If the plug does not fit into outlet, contact a qualified
electrician to install the proper outlet. Do not change the
plug in any way.

If the power cord is damaged, it must be replaced

by the manufacturer, its service agent or a similarly

qualified person in order to avoid a hazard.

This operator is a plug in domestic appliance and is

designed for indoor use only. It must be installed in a

dry position that is protected from the weather.

The opener is not intended for use by young children

or infirm persons without supervision.

WARNING! It is vital for the safety of

persons to follow all instructions. Save

these instructions.

Diamond PD

Power Drive

: Instruction Manual

PA1000

Instruction Manual (Instructions d’installation)

Содержание PA1000V1




































Результаты поиска

Содержание PA1000V1

Отзывы:

Похожие инструкции для PA1000V1

Бренды по названию

Популярные бренды

Automatic Technology PA1000V1, Инструкция по эксплуатации

Результаты поиска

Содержание PA1000V1

Отзывы:

Похожие инструкции для PA1000V1

Бренды по названию

Популярные бренды