Automatic Technology CB-19 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 28

Automatic Technology CB-19 Скачать руководство пользователя страница 23

REMOTE CODE SET PROCEDURE

22

NOTE ONLY THE FUNCTION OF THE EXISTING TRANSMIT-
TER BUTTON CAN BE ASSIGNED TO THE NEW TRANSMIT-
TER. PLEASE READ THE INSTRUCTION PRIOR TO CARRY-
ING OUT THE STEPS AS THE PROCEDURE HAS A TIMEOUT
FACILITY FOR SECURITY REASONS.

STEP 1 SELECTING THE FUNCTION TO BE CODED

Using the existing transmitter, operate the gate with the transmit-
ter button which has the function to be coded.
As an example the existing transmitters Button 1 has been coded
with the OSC function assigned to it.

STEP 2. WAIT FOR GATE TO COMPLETE CYCLE

If the button’s function activates the gate (PED, SWP, OSC, CLS,
STP or OPN) wait for the gate to complete its cycle.

STEP 3. ACTIVATE REMOTE CODE SET MODE

Using a small needle press and hold firmly for two
seconds through the Coding Hole of the existing transmitter.

STEP 4.

.

CODE NEW TRANSMITTER BUTTON

Within 10 seconds, activate the new transmitters button you wish
to code for 2 seconds. The example shows Button 1 being used
but it could be any button. It can even be an unused button on the
existing transmitter

STEP 5.

.

CONFIRM TRANSMITTER BUTTON TO BE

CODED

Within 10 seconds, activate the new transmitters button again for
2 seconds for confirmation

STEP 6.

.

TEST OPERATION

The new transmitter button should now function as the existing
transmitter button did.

NOTE ON CODED TRANSMITTER’S ID LABEL

When a transmitter is remote coded, its ID label is set that that of
the existing transmitter. If the existing transmitter does not have
an ID label assigned, then the ID label of the new transmitter is
set to:

R/C Tx ###

where ### is the existing transmitters

store number. This ensures that the originator of any remote coded
transmitter can be identified

THE CONTROLLER PROVIDES A REMOTE CODE SET FEATURE WHERE BY AN EXISTING TRANSMITTER

BUTTON CAN BE USED TO CODE A NEW TRANSMITTER BUTTON INTO THE CONTROLLER MEMORY.

Operate Gate Using Existing Transmitter Button

Activate Remote Code Set Mode

Operate New Transmitter Button To Be Coded

Existing

New

Confirm New Transmitter Button To Be Coded

New

«
...
21
22
23
24
25
...
»

Содержание CB-19





























Отзывы:

Нет отзывов