manualshive.com logo in svg

Autel MaxiCharger, Руководство пользователя

Поделиться
Скачать
Autel MaxiCharger Скачать руководство пользователя страница 5

1 

 

 

Using This Manual 

This manual provides the installation and operation procedures of the MaxiCharger DC 
Wall  Mount  (hereinafter  referred  to  as  MaxiCharger).  Read  through  this  manual  and 
become familiarized with the instructions of the MaxiCharger prior to installation to ensure 
a successful installation and operation process. 

Some illustrations shown in this manual may contain modules and optional equipment 
that are not included in your system. Contact your sales representative for availability of 
other modules and optional tools or accessories. 

The document is intended for these groups: 

 

Owner of the MaxiCharger (see 

Owner Responsibilities

) 

 

Installation engineer (see 

Installation Engineer Qualifications

) 

  Conventions 

  Bold Text 

Bold text is used to highlight selectable items such as buttons and menu options.   

  Notes 

 

NOTE

:  provides  helpful  information  such  as  additional  explanations,  tips,  and 

comments. 

 

IMPORTANT

: indicates a situation that, if not avoided, may result in damage to the 

test equipment or vehicle. 

 

DANGER

:  indicates  an  imminently  hazardous situation  which,  if  not  avoided,  will 

result in death or serious injury to the operator or bystanders. 

 

WARNING

: indicates a potentially hazardous situation which, if not avoided, could 

result in death or serious injury to the operator or to bystanders. 

 

CAUTION

:  indicates  that  disobeying  the  instruction  can  cause  damage  to  the 

equipment or property. 

  Hyperlinks 

Hyperlinks are available in electronic documents. Blue italic text  indicates a selectable 
hyperlink and blue underlined text indicates a website link or an email address link. 

Содержание MaxiCharger























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды