manualshive.com logo in svg

Autel MaxiCharger, Руководство пользователя

Поделиться
Скачать
Autel MaxiCharger Скачать руководство пользователя страница 6

2 

 

 

Safety 

  Safety Warnings 

 

Disconnect  the  power  supply  to  the  MaxiCharger  during  the  entire  installation 
procedure. 

 

The load capacity of the grid must meet the requirements of the MaxiCharger. 

 

Connect  the  MaxiCharger  to  a  grounded,  metal,  permanent  wiring  system. 
Otherwise, use the equipment-grounding conductor with the circuit conductors and 
connect it to the equipment grounding terminal or lead on the product. 

 

Unqualified  personnel  must  keep  a  safe  distance  during  the  entire  installation 
procedure. 

 

The connections to the MaxiCharger must comply with all applicable local rules. 

 

Only  use  electrical  wires  of  sufficient  gauge  and  insulation  to  handle  the  rated 
current and voltage demand. 

 

Protect  the  wiring  inside  the  MaxiCharger  from  damage  and  do  not  obstruct  the 
wiring when you perform maintenance on the cabinet. 

 

Keep the cabinet away from all water source. 

 

Protect  the  MaxiCharger  with  safety  devices  and  measures  as  specified  by  local 
rules. 

 

Wear  proper  personal  protective  equipment  such  as  protective  clothing,  safety 
gloves, safety shoes, and safety glasses when necessary. 

  Owner Responsibilities 

The MaxiCharger owner runs the MaxiCharger for commercial or business purposes for 
itself or third-party usage. To protect the user, other employees, or third parties, the owner 
bears  legal  responsibility  for  the  operation  of  the  charger  and  has  the  following 
responsibilities: 

 

Identify  any  hazards  (in  terms  of  a  risk  assessment)  resulting  from  the  working 
conditions on the site. 

 

Know and implement all local rules. 

 

Install protective devices before operating the MaxiCharger. 

 

Make sure all protective devices are installed after installation or maintenance work. 

 

Prepare  an  emergency  plan  that  instructs  people  what  to  do  in  case  of  an 
emergency. 

Содержание MaxiCharger























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды