manualshive.com logo in svg

Autel MaxiCharger, Руководство пользователя

Поделиться
Скачать
Autel MaxiCharger Скачать руководство пользователя страница 7

3 

 

 

Make sure that all employees and third parties are qualified in accordance with the 
applicable local rules to perform their work. 

 

Make  sure  that  there  is  sufficient  space  around  the  MaxiCharger  to  safely  do 
maintenance and installation work. 

 

Identify a site operator who is responsible for the safe operation of the MaxiCharger 
and for the coordination of all work, if the owner does not do these tasks.

 

 

Make sure that all qualified installation engineers obey local rules and  installation 
instructions, and adhere to the specifications of the MaxiCharger.

 

  Installation Engineer Qualifications 

The installation engineers must: 

 

Be qualified in accordance with all applicable local rules to do the work. 

 

Be completely familiar with the MaxiCharger and its safe installation. 

 

Obey all local rules and the instructions in the installation manual. 

  Usage Instructions 

Do  not  use  the  MaxiCharger  and  immediately  contact  the  manufacturer  if  any  of  the 
following situations occur: 

 

Damaged enclosure 

 

Damaged EV charging cable or connector 

 

Expose to lightning 

 

Expose to water 

 

Expose to nature disaster, fire or smoke 

  Symbols on the MaxiCharger 

Table 2-1 Symbol Description 

Symbol 

Risk Description 

 

General risk 

 

Hazardous voltage with risk of electrocution 

Содержание MaxiCharger























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды