Autel MaxiCharger Скачать руководство пользователя страница 53

Страница: 53 / 54

Issue

Possible
Cause

Solution

Handler

Local network
failure

Check local network
connection.

Customer
Technical
Support/

Autel
Technical
Support

RFID Card
Reading Failure

The RFID card
is not
recognized.

The RFID card broken.
No RFID card data on the
cloud.
Use a new RFID card.

Customer
Technical
Support

Insufficient
balance

Contact the operator for
top-up.

Customer
Technical
Support

Internet failure

See "QR Code Scanning
Failure" solutions above.

Customer
Technical
Support/

Autel
Technical
Support

Charging Failure

The connector
is not properly
connected.

Check the connector
connection and
reconnect it.
Try another MaxiCharger
to charge the EV.

Customer
Technical
Support/

Autel
Technical
Support

EV error

Try another MaxiCharger
to charge the EV.
Contact your EV
manufacturer for support.

EV dealer/

EV
manufacturer

Charger error

Try another MaxiCharger
to charge the EV.
Contact Autel technical
support.

Customer
Technical
Support/

Autel
Technical
Support

Содержание MaxiCharger























































Результаты поиска

Содержание MaxiCharger

Отзывы:

Похожие инструкции для MaxiCharger

Бренды по названию

Популярные бренды

Autel MaxiCharger, Руководство пользователя

Результаты поиска

Содержание MaxiCharger

Отзывы:

Похожие инструкции для MaxiCharger

Бренды по названию

Популярные бренды