AudioCodes Media Pack MP-112 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 486

background image

SIP User's Manual

62

Document #: LTRT-65412

MP-11x & MP-124

Parameter

Description

Web/EMS: Gateway

[InterfaceTable_Gateway]

Defines the IP address of the default gateway used by the
device.



Notes:

Only one default gateway can be defined



.



The default gateway must be configured on an interface
that includes Media traffic.



The default gateway's IP address must be in the same
subnet as the interface address.

Apart from the interface with the defined default gateway,
for all other interfaces define this parameter to “0.0.0.0”



.

Web/EMS: VLAN ID

For configuring additional routing rules for other interfaces,
use the Routing table (refer to Configuring the IP Routing
Table on page

65

).

Defines the VLAN ID for each interface.

[InterfaceTable_VlanID]

Incoming traffic with

this VLAN ID is routed to the corresponding interface, and
outgoing traffic from that interface is tagged with this VLAN
ID.

Notes:



The VLAN ID must be unique for each interface



VLANs are available only when booting the device from
flash. When booting using BootP/DHCP protocols, VLANs
are disabled to allow easier maintenance access. In this
scenario, multiple network interface capabilities are not
available.

.

Web/EMS: Interface Name

Defines a string (up to 16 characters) to name this interface.
This name is displayed in management interfaces (Web

[InterfaceTable_InterfaceName]

, CLI

and SNMP) for better readability (and has no functional use)
as well as the 'SIP Media Realm' table (refer to Configuring
Media Realms).

Note:

The interface name is a mandatory parameter and must

be unique for each interface.

General Parameters

VLAN Mode

[VlANMode]

For a description of this parameter, refer to Networking
Parameters on page

213

.

Native VLAN ID

[VLANNativeVlanID]

For a description of this parameter, refer to Networking
Parameters on page

213

.

3.3.1.2 Configuring the Application Settings

The 'Application Settings' page is used for configuring various application parameters such
as Network Time Protocol (NTP), daylight saving time, and Telnet. For a description of
these parameters, refer to “Configuration Parameters Reference” on page

213

.

«
...
60
61
62
63
64
...
»

Содержание Media Pack MP-112







































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Pack MP-112

Бренд: WAGO Страницы: 78

DRY CONTACT GATEWAY SDG-01

Бренд: Sinclair Страницы: 20

P-660R-T Series

Бренд: ZyXEL Communications Страницы: 9

Бренд: Dinstar Страницы: 92

Бренд: Rose Point Страницы: 27

Бренд: MCK Страницы: 18

Бренд: ioLIVING Страницы: 13

Бренд: TEKTELIC Communications Страницы: 8

Бренд: ZyXEL Communications Страницы: 2

Бренд: ZyXEL Communications Страницы: 2

Бренд: AudioCodes Страницы: 418

PowerMaster-360

Бренд: Visonic Страницы: 65

Бренд: Universal Remote Control Страницы: 26

Бренд: Schlage Страницы: 15

Бренд: SmartRG Страницы: 16

Бренд: Philio Technology Corporation Страницы: 40

SmartCast Wireless Gateway

Бренд: Cree Страницы: 2

Бренд: H3 System Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды