manualshive.com logo in svg

Audi 2003 A8, Руководство по ремонту, Страница: 181 / 252

Поделиться
Скачать
Audi 2003 A8 Скачать руководство пользователя страница 181

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not 
 permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability 
     with respect to the correctness of information in this document. Copyright by AUDI AG.

– Remove bolts -arrows-.
– Detach cover -2- with hose -1- for crankcase breather system.

– Pull out oil retention valve -1- and spray nozzle valve -2-.
Installing
Installation is carried out in the reverse order; note the following:

Note

♦

Renew the bolts tightened with specified tightening angle.

♦

Renew gaskets and O-rings.

– Install high-pressure pipes ⇒  Rep. gr.  24 ; Removing and

installing injectors .

– Install intake manifold ⇒  Rep. gr.  24 .
Tightening torques
♦

⇒ “1.7 Oil retention valve and spray nozzle valve - exploded

view”, page 173

1.9

Removing and installing hose for crank‐

case breather system

Removing
– Remove intake manifold ⇒  Rep. gr.  24 .
– Remove bolt -arrow- and pull out crankcase breather hose

-1- from cover -2-.

Installing
Installation is carried out in the reverse order; note the following:

Note

Renew O-ring.

– Install intake manifold ⇒  Rep. gr.  24 .
Tightening torques
♦

⇒ “1.7 Oil retention valve and spray nozzle valve - exploded

view”, page 173

1.10

Oil filter housing - exploded view

Audi A8 2003 ➤

10-cylinder direct petrol injection engine (5.2 ltr. 4-valve), mechanics - Edition 10.2013

1. Lubrication system    

175

Содержание 2003 A8





























































































































































































































































Отзывы:

Нет отзывов