AuCom EMX4i Скачать руководство пользователя страница 30

Страница: 30 / 126

INSTALLATION

710-14888-00C EMX4i User Manual

The power input and output terminals for EMX4 are at the bottom of the unit.

•

Models EMX4i-0024B~EMX4i-0135B use cage clamps. Use only copper
stranded or solid conductors, rated for 75 ºC or higher.

•

Models EMX4i-0184B~EMX4i-0580B use busbars. Use copper or
aluminium conductors, stranded or solid, rated for 60 ºC/75 ºC.

EMX4i-0024B~EMX4i-0135B

Cable size:
6-70 mm

(AWG 10-2/0)

Torque: 4 Nm (2.9 ft-lb)

Torx T20 x 150

Flat 7 mm x 150

14 mm (0.55 inch)

EMX4i-0184B~EMX4i-0250B

EMX4i-0352B~EMX4i-0580B

19 Nm (14.0 ft-lb)

66 Nm (49.0 ft-lb)

6 mm

20 mm

9 mm

(M8)

17045.

6 mm

34 mm

13 mm

(M12)

17047.

NOTE
If the installation requires large diameter cables, it is possible to complete
each termination with two smaller cables, one on each side of the busbar.

UL Compliant Installation

For models EMX4i-0184B to EMX4i-0580B to be UL compliant, you must use the
recommended pressure terminal/connector.

Model

Recommended lugs part No.

EMX4i-0184B

EMX4i-0200B

OPHD 185-10

EMX4i-0229B

EMX4i-0250B

EMX4i-0352B

EMX4i-0397B

OPHD 150-12

EMX4i-0410B

EMX4i-0550B

OPHD 240-12

EMX4i-0580B

Содержание EMX4i































































































































Результаты поиска

Содержание EMX4i

Отзывы:

AuCom EMX4i, Руководство пользователя, Страница: 30 / 126

Результаты поиска

Содержание EMX4i

Отзывы: