manualshive.com logo in svg

AuCom EMX4i, Руководство пользователя, Страница: 120 / 126

Поделиться
Скачать
AuCom EMX4i Скачать руководство пользователя страница 120

TROUBLESHOOTING 

710-14888-00C  EMX4i User Manual   

 

119

 

Display 

Possible cause/Suggested solution 

Power loss 

This trip is not adjustable. 
The starter is not receiving mains supply on one or more phases 
when a Start Command is given. 
Check that the main contactor closes when a start command is 
given, and remains closed until the end of a soft stop. Check the 
fuses. If testing the soft starter with a small motor, it must draw 
at least 10% of the starter’s programmed FLC setting on each 
phase.   
Related parameters: None 

Pressure Sensor 

The smart card has detected a fault with the pressure sensor. 
Related parameters: 30A, 36A 

Rating Capacity 

The EMX4i is operating beyond its safe capacity.    Allow the 
starter to cool. 
Related parameters: None 

RTD Circuit 

The smart card has detected a fault with the RTD sensor, or the 
RTD has activated temperature protection. 
Related parameters: 35B, 36J 

SCR Itsm 

The SCR current surge rating has been exceeded. 
Related parameters: None 

SCR 
overtemperature 

The temperature of the SCRs, calculated by the thermal model, is 
too high to allow further operation.    Wait for the starter to cool. 
Related parameters: None 

Starter 
communication 

There is a problem with the connection between the soft starter 
and the optional expansion card. Remove and reinstall the card. If 
the problem persists, contact your local distributor. 
Related parameters: None   

Starts per hour 

The soft starter has already attempted the maximum number of 
starts in the last 60 minutes. Wait before attempting another 
start. 
To determine when the waiting period will end, review the log. 
Related parameters: 5Q 

Thermistor circuit 

The thermistor input has been enabled and: 

•

 

The resistance at the input has fallen below 20 

Ω

 (the cold 

resistance of most thermistors will be over this value) or 

•

 

A short circuit has occurred. Check and resolve this condition. 

Related parameters: None 

Содержание EMX4i































































































































Отзывы:

Нет отзывов