AuCom EMX4i страница 106 Скачать руководство пользователя

Страница: 106 / 126

PROGRAMMABLE PARAMETERS

710-14888-00C EMX4i User Manual

105

9.22

34 Depth Protection

NOTE
The parameters in this group are only active if a smart card is installed.

Depth protection uses terminals B13, B14 or C13, C14 on the smart card.

34A –

Depth Trip Level

Range:

0 – 1000

Default:

Description:

Sets the trip point for depth protection.

34B –

Depth Reset Level

Range:

0 – 1000

Default:

Description:

Sets the level for the soft starter to auto-reset a depth trip.

34C –

Depth Start Delay

Range:

00:00:10 – 30:00:00 mm:ss:ms Default:

00:00:500 ms

Description:

Sets a delay before a depth protection trip can occur. The delay
is counted from the time a start signal is received. The depth
input is ignored until the start delay has elapsed.

34D –

Depth Response Delay

Range:

00:00:10 – 30:00:00 mm:ss:ms Default:

00:00:500 ms

Description:

Sets a delay between the depth passing the depth protection trip
level, and the soft starter tripping.

9.23

35 Thermal Protection

NOTE
The parameters in this group are only active if a smart card is installed.

35A –

Temperature Sensor Type

Options:

None (default)
PT100

Description:

Selects which type of sensor is associated with the temperature
sensor input on the smart card.

35B –

Temperature Trip Level

Range:

0° – 240°

Default:

40°

Description:

Sets the trip point for temperature protection. Use parameter
10B

Temperature Scale

to configure the temperature scale.

Содержание EMX4i































































































































Результаты поиска

Содержание EMX4i

Отзывы:

Похожие инструкции для EMX4i

Бренды по названию

Популярные бренды

AuCom EMX4i, Руководство пользователя

Результаты поиска

Содержание EMX4i

Отзывы:

Похожие инструкции для EMX4i

Бренды по названию

Популярные бренды