AuCom EMX4i страница 25 Скачать руководство пользователя

Страница: 25 / 126

INSTALLATION

EMX4i User Manual 710-14888-00C

Installation

WARNING
Do not apply mains voltage to the starter until all wiring is complete.

WARNING
Always apply control voltage before (or with) mains voltage.

4.1

Command Source

The EMX4i can be started and stopped via the digital inputs, remote keypad,
communication network, smart card or scheduled auto-start/stop. The command
source can be set via the Setup Tools, or using parameter 1A

Command Source

4.2

Setup Procedure Overview

Mount the soft starter (refer to

Physical Installation

on page 14 for details).

Connect control wiring (refer to

Input Terminals

on page 25 for details).

Apply control voltage to the starter.

Configure your application:
1.

Press MENU to open the Menu.

Press to open the Quick Setup menu.

Scroll through the list to find your application, then press to begin the
configuration process (refer to

Quick Setup

on page 33 for details).

If your application is not listed in Quick Setup:
1.

Press to return to the Menu.

Use to scroll to Main Menu and press .

Scroll to Motor Details and press , then press again to edit
parameter 1B

Motor Full Load Current

Set parameter 1B to match the motor's full load current (FLC).

Press to save the setting.

Close the Menu by pressing repeatedly.

(Optional) Use the built-in simulation tools to check that the control wiring is
connected correctly (refer to

Run simulation

on page 35).

Power off the soft starter.

Connect the motor cables to starter output terminals 2/T1, 4/T2, 6/T3.

10.

Connect mains supply cables to starter input terminals 1/L1, 3/L2, 5/L3 (refer
to

Power Terminations

on page 28).

The soft starter is now ready to control the motor.

Содержание EMX4i































































































































Результаты поиска

Содержание EMX4i

Отзывы:

Похожие инструкции для EMX4i

Бренды по названию

Популярные бренды

AuCom EMX4i, Руководство пользователя

Результаты поиска

Содержание EMX4i

Отзывы:

Похожие инструкции для EMX4i

Бренды по названию

Популярные бренды