manualshive.com logo in svg

ATSI PCMT-8000, Руководство пользователя

Поделиться
Скачать
ATSI PCMT-8000 Скачать руководство пользователя страница 50

7.  Test Descriptions

9. Monitor AC line is set to 100.5 Vrms.
10. Monitor AC line is decreased by approximately 0.25Vrms.
11. PCMT Watchdog signal is turned off.
12. Delay.
13. Check for monitor fault state.
14. If monitor is found in fault continue, else go to step (20). 
15. Increase AC line voltage by 15Vrms.
16. PCMT Watchdog signal is turned on.
17. Reset the monitor.
18. Decrease AC line voltage by 15Vrms.
19. Go to step (10).  Repeat until AC line is less than 96Vrms.
20. Record the AC line voltage.
21. PCMT Watchdog signal is turned off.
22. Increase AC line voltage by approximately 0.25Vrms.
23. Delay.
24. Check for monitor fault state.
25. If monitor found in fault or if AC line is greater than 115Vrms continue, else go to step (22).
26. Record the AC line voltage

Monitor Response to PASS

 :

AC line voltage at (20) must be between 96 and 100Vrms.  AC line voltage at (26) must be between 101 and 
105Vrms.  The difference between the voltage at (26) and (20) must be a minimum of 3 Vrms.  

RED/GRN/YEL Single Channel

Test Description :

Line voltage is applied to each RED, GRN, and YEL input one at a time to verify that a single input will not cause the 
monitor to go into the fault state.

Test Sequence :

1. Monitor is powered up in the quiescent state.
2. AC line voltage is applied to RED1 for 750ms.
3. AC line voltage is applied to GRN1 for 750ms.
4. AC line voltage is applied to YEL1 for 3600ms.
5. AC line voltage is applied to RED1.
6. Repeat 2 through 5 for each channel.

Monitor Response to PASS

 :

Monitor must NOT be found in fault.

GRN/YEL Single Channel

Test Description :

Line voltage is applied to each, GRN, and YEL input one at a time to verify that a single input will not cause the 
monitor to go into the fault state.

Test Sequence :

1. Monitor is powered up in the quiescent state.
2. AC line voltage is applied to GRN1 for 750ms.
3. AC line voltage is applied to YEL1 for 3600ms.
4. Repeat 2 through 3 for each channel.

Monitor Response to PASS

 :

Monitor must NOT be found in fault.

Short YEL

Test Description :

Apply the GRN, YEL, RED sequence to each channel with a 2 second YEL to verify that the monitor will go into the 
fault state. 

PCMT-8000 User's Manual

Rev. 1.7

49 of 80

Содержание PCMT-8000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды