manualshive.com logo in svg

ATSI PCMT-8000, Руководство пользователя

Поделиться
Скачать
ATSI PCMT-8000 Скачать руководство пользователя страница 15

7.  Test Descriptions

7. 

Test Desc

 

 riptions

 

 

All of the PCMT-8000 tests described below are based on the published standard that is listed.  It is the intent of ATSI to 
test all of the requirements of the listed standard as thoroughly as possible.  The tests are based on our best interpretation 
of the standards and are subject to the limitations of what is practical and feasible in a simulated testing environment.

Each individual jurisdiction (i.e. state, county, city) may have specific requirements or practices that are routinely followed 
which deviate from the applicable standard or ignore certain parts.  Furthermore, some monitor manufacturers may have 
certain features enabled or disabled in their devices to accommodate such deviations from the applicable standard.  
Therefore, the user has the option of disabling certain tests.  These tests are listed as “optional” in the Test Setup window. 

There may also be certain tests that are related to monitor functions that deviate from the applicable standard.  These 
deviations my be due to special features that have been added and are not yet covered in the standard.  There may also 
be cases where monitors are old and have been manufactured according to the requirements of a previous version of the 
applicable standard.  In such cases, special tests may be provided to accommodate these deviations from the current 
version of the standard.  

It is the responsibility of the user to determine what tests are appropriate for their local 

requirements.

  

    

7.1. 

NEMA TS1 Test Descriptions 

These tests are based on the requirements of 

NEMA Standard TS-1-1994

.

7.1.1

 System / Timing Tests

 

Interlock Sensing

Test Description :

Verify that the Interlock input is working.

Test Sequence :

1.  Interlock input set at 24V.
2.  Check Interlock output.
3.  Interlock input set at 0V.
4.  Check Interlock output.

Monitor Response to PASS :

State of Interlock output identical to Interlock input.

Power Failure Ignore

Test Description :

Verify the monitor ignores an AC power interrupt lasting less than 450ms.

Test Sequence :

1. Monitor is powered up in the quiescent state.  
2. Monitor AC power is turned off for less than 450ms and then back on.
3. Fault state is checked.

Monitor Response to PASS :

Loss of AC power for less than 450ms must NOT cause fault.  

Power Failure Detect

Test Description :

Verify the monitor recognizes an AC power interrupt lasting more than 500ms.

Test Sequence :

1. Monitor is powered up in the quiescent state.  

PCMT-8000 User's Manual

Rev. 1.7

14 of 80

Содержание PCMT-8000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды