manualshive.com logo in svg

ATSI PCMT-8000, Руководство пользователя

Поделиться
Скачать
ATSI PCMT-8000 Скачать руководство пользователя страница 2

Table of Contents

1. Explanation of Symbols, Terms, and Abbreviations........................................................................................................... 3

2. Safety Information............................................................................................................................................................. 4

3. Introduction........................................................................................................................................................................ 5

4. PCMT-8000 Test Manager Software Installation................................................................................................................ 6

4.1. Computer Requirements........................................................................................................................................... 6
4.2. PCMT-8000 Interface Software Installation............................................................................................................... 6
4.3. PCMT-8000 USB Driver Installation.......................................................................................................................... 6

5. Preparing to Test............................................................................................................................................................... 7

5.1. Setting Up the PCMT................................................................................................................................................. 7
5.2. Preparing the Monitor to Test..................................................................................................................................... 7
5.3. Monitor Switch Settings............................................................................................................................................. 8

6. Using the Test Manager Software...................................................................................................................................... 9

6.1. Monitor Info................................................................................................................................................................ 9
6.2. Test Setup................................................................................................................................................................ 10
6.3. Settings.................................................................................................................................................................... 11
6.4. PCMT Info .............................................................................................................................................................. 12
6.5. Report Viewer.......................................................................................................................................................... 12
6.6. Help......................................................................................................................................................................... 12
6.7. Starting a Test.......................................................................................................................................................... 12

7. Test Descriptions............................................................................................................................................................. 14

7.1. NEMA TS1 Test Descriptions .................................................................................................................................. 14

7.1.1 System / Timing Tests ...................................................................................................................................... 14
7.1.2 Voltage Tests.................................................................................................................................................... 18
7.1.3 Optional Tests................................................................................................................................................... 19

7.2. NEMA TS2 Test Descriptions................................................................................................................................... 24

7.2.1 System / Timing Tests ...................................................................................................................................... 24
7.2.2 Voltage Tests.................................................................................................................................................... 29
7.2.3 Optional Tests................................................................................................................................................... 32
7.2.4 Optional Tests (MMU2 FYA)............................................................................................................................. 37

7.3.  System 170 Type 210 Test Descriptions................................................................................................................. 42

7.3.1 System / Timing Tests....................................................................................................................................... 42
7.3.2 Voltage Tests.................................................................................................................................................... 47
7.3.3 Optional Tests................................................................................................................................................... 48

7.4. System 270 Type 2010 / LADOT 2018 Test Descriptions........................................................................................53

7.4.1 System / Timing Tests....................................................................................................................................... 53
7.4.2 Voltage Tests.................................................................................................................................................... 59
7.4.3 Optional Tests................................................................................................................................................... 61

7.5 Canadian Fast Flash Test Descriptions.................................................................................................................... 66

8. Troubleshooting............................................................................................................................................................... 68

9. Electrical and Mechanical Specifications......................................................................................................................... 69

10. Service and Calibration.................................................................................................................................................. 70

11. Limited Warranty and Liability........................................................................................................................................ 71

12. Packing Your PCMT for Shipment................................................................................................................................. 72

13. Return Merchandise Form............................................................................................................................................. 73

Appendix A. Connecting multiple testers to one computer...................................................................................................74

Appendix B. Flashing Yellow Arrow (FYA) Mapping............................................................................................................. 76

PCMT-8000 User's Manual

Rev. 1.7

1 of 80

Содержание PCMT-8000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды