manualshive.com logo in svg

ATSI PCMT-8000, Руководство пользователя

Поделиться
Скачать
ATSI PCMT-8000 Скачать руководство пользователя страница 31

7.  Test Descriptions

1. Monitor is powered up in the quiescent state.
2. Redenable input is activated.
3. A negative rectified sine wave greater than 70Vrms is applied to each RED channel.

Monitor Response to PASS

 :

Monitor must NOT be found in fault state.

RED 50Vrms Sine Wave Recognition

Test Description :

Verify that a sign wave less than 50Vrms is recognized as being "off" for every RED channel input.  

Test Sequence :

1. Monitor is powered up in the quiescent state.
2. All RED channels are at AC line voltage.
3. Redenable input is activated. 
4. A sine wave less than 50Vrms is applied to each RED channel one at a time.
5. fault state is checked for each channel.

Monitor Response to PASS

 :

50Vrms on any RED channel must cause monitor to go into fault state (Redfail fault).

RED 50Vrms Positive Rectified Recognition

Test Description :

Verify that a positive rectified sign wave less than 50Vrms is recognized as being "off" for every RED channel input.  

Test Sequence :

1. Monitor is powered up in the quiescent state.
2. All RED channels are at AC line voltage.
3. Redenable input is activated. 
4. A positive rectified sine wave less than 50Vrms is applied to each RED channel one at a time.
5. fault state is checked for each channel.

Monitor Response to PASS

 :

50Vrms on any RED channel must cause monitor to go into fault state (Redfail fault).

RED 50Vrms Negative Rectified Recognition

Test Description :

Verify that a negative rectified sign wave less than 50Vrms is recognized as being "off" for every RED channel input.  

Test Sequence :

1. Monitor is powered up in the quiescent state.
2. All RED channels are at AC line voltage.
3. Redenable input is activated. 
4. A negative rectified sine wave less than 50Vrms is applied to each RED channel one at a time.
5. fault state is checked for each channel.

Monitor Response to PASS

 :

50Vrms on any RED channel must cause monitor to go into fault state (Redfail fault).

GRN, YEL, WLK 25Vrms Recognition (Sine Wave, Positive Rectified, Negative Rectified)

Test Description :

Verify that the monitor recognizes a signal greater than 25Vrms as being "on" for every GYW channel. 

Test Sequence :

1. Monitor is powered up in the quiescent state.

PCMT-8000 User's Manual

Rev. 1.7

30 of 80

Содержание PCMT-8000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды