manualshive.com logo in svg

Atrie DB 120, Руководство пользователя

Поделиться
Скачать
Atrie DB 120 Скачать руководство пользователя страница 14

                                                                 

Atrie DB-120 User Manual

 

User Manual 

14

connection setup page is displayed; figure 7 illustrates a typical DHCP configuration.  Give your 
DHCP connection a unique name; the name must not have spaces and cannot begin with numbers.  In 
this case the unique name is called 

DHCP1

.  Select the encapsulation type (LLC or VC); if you are 

not sure just use the default mode.  Select the VPI and VCI settings; your DSL service provider or 
your ISP will supply these; in this case the DSL service provider is using 

0,35

.  Also select the quality 

of service (QOS); leave the default value if you are unsure or the ISP did not provide this information.   
 
If your DSL line is connected and your DSL/IPS provider is supporting DHCP, you can click the 
renew button and the gateway will retrieve an IP address, Subnet mask, and Gateway address.  At 
anytime, you can renew the DHCP address by clicking on the renew button; in most cases you will 
never have to use this button. 
 
 

 

 

Figure 7 (DHCP Connection Setup) 

 
To complete the connection you must now click the apply button.  The apply button will temporarily 
save this connection. To make the change permanent you need to click on 

Tools

 (at the top of the 

page) and select 

System Commands

.  At the system commands page, click on 

Save All

. 

 

3.4.1.5

 

STATIC CONNECTION SETUP 

Static is used whenever a known static IP is assigned. The accompanying information such as the 
Subnet mask and the gateway should also be specified. Up to three Domain Name Server (DNS) 
addresses can also be specified. These servers would enable you to have access to other web servers. 
Valid IP addresses range is from 0.0.0.0 to 255.255.255.255.  
 
To configure the gateway for a Static connection, click on Setup and then click on 

New Connection

.  

The default Static connection setup is displayed.  At the Type field select

 Static

 and the Static 

connection setup page is displayed; figure 8 illustrates a typical Static configuration.  Give your Static 
connection a unique name; the name must not have spaces and cannot begin with numbers.  In this 
case the unique name is called 

STATIC1

.  Select the encapsulation type (LLC or VC); if you are not 

sure just use the default mode.  Select the VPI and VCI settings; your DSL service provider or your 
ISP will supply these; in this case the DSL service provider is using 

0,35

.  Also select the quality of 

Содержание DB 120


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды