manualshive.com logo in svg

Atrie DB 120, Руководство пользователя

Поделиться
Скачать
Atrie DB 120 Скачать руководство пользователя страница 12

                                                                 

Atrie DB-120 User Manual

 

User Manual 

12

 

 

Figure 5 (PPPoA Connection Setup) 

 

To complete the connection you must now click the apply button.  The apply button will temporarily 
save this connection. To make the change permanent you need to click on 

Tools

 (at the top of the 

page) and select 

System Commands

.  At the system commands page, click on 

Save All

. 

 

3.4.1.3

 

PPPoE CONNECTION SETUP 

 

PPPoE is also known as RFC 2516. It is a method of encapsulating PPP packets over Ethernet. PPP or 
Point-to-Point protocol is a method of establishing a network connection/session between network 
hosts. It usually provides a mechanism of authenticating users.  
 
To configure the gateway for PPPoE, click on Setup and then click on 

New Connection

.  The default 

PPPoE connection setup is displayed.  At the Type field select 

PPPoE

 and the PPPoE connection 

setup page is displayed; figure 6 illustrates a typical PPPoE configuration.  Give your PPPoE 
connection a unique name; the name must not have spaces and cannot begin with numbers.  In this 
case the unique name is called 

PPPOE1

.  Select the encapsulation type (LLC or VC); if you are not 

sure just use the default mode.  Select the VPI and VCI settings; your DSL service provider or your 
ISP will supply these; in this case the DSL service provider is using

 0,30

.  Also select the quality of 

service (QOS); leave the default value if you are unsure or the ISP did not provide this information.   
 
Following is a description of the different options: 

j.

 

Username: The username for the PPPoE access; this is provided by your DSL service 
provider or your ISP. 

k.

 

Password: The password for the PPPoE access; this is provided by your DSL service 
provider or your ISP. 

l.

 

On-Demand: Enables on-demand mode. The connection will disconnect if no activity is 
detected after the specified idle timeout value. 

m.

 

Idle Timeout: Specifies that PPPoE connection should disconnect if the link has no 
activity detected for n seconds.  This field is used in conjunction with the On-Demand 
feature. To ensure that the link is always active, enter a 0 in this field. 

Содержание DB 120


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды