10.10
10.10
Electrical
Electrical system
system
A
AT
TL
LE
ET
T
S
SE
ER
RV
VIIC
CE
E
M
MA
AN
NU
UA
AL
L
B
Baatttteerry
y
10
10.2
.2.3
.3
Ba
Batt
tter
ery p
y par
aram
amet
eter
ers fr
s from v
om ver
ersi
sion 3
on 3.0
.00
0
Select 48V
Select 48V
batt.
batt.
Nominal batter
Nominal battery voltage, state
y voltage, state 1 for 48
1 for 48 V
Volt, 0 for
olt, 0 for 24 V
24 Volt. 48 V
olt. 48 Volt is
olt is
Default.
Default.
Measured B+
Measured B+
(mV)
(mV)
Actual battery voltage
Actual battery voltage to A
to ATC. You can make corrections
TC. You can make corrections for voltage
for voltage
losses in cables and contactors up to the ATC by changing these values.
losses in cables and contactors up to the ATC by changing these values.
To make the correction, measure the battery voltage at the poles using a
To make the correction, measure the battery voltage at the poles using a
voltmeter that can
voltmeter that can show 4 digits at 50 Volts, then state the voltage in mV.
show 4 digits at 50 Volts, then state the voltage in mV.
(If the voltmete
(If the voltmeter shows 48.12 V
r shows 48.12 Volt, press 48120 Ent).
olt, press 48120 Ent).
Battery size
Battery size
(Ah)
(Ah)
Stated in Ah. This is normally stated on the battery. Default is 550.
Stated in Ah. This is normally stated on the battery. Default is 550.
Pump size
Pump size
(kW)
(kW)
State in whole kW. Default is 14.
State in whole kW. Default is 14.
Utilisatio
Utilisation
n (%)
(%)
Usage, stated from 50 to 200 per cent, and used to correct for light/hard
Usage, stated from 50 to 200 per cent, and used to correct for light/hard
driving. Default is 100. Higher values are used with harder driving, lower
driving. Default is 100. Higher values are used with harder driving, lower
values for lighter driving.
values for lighter driving.
Chassis
Chassis
con
const
st.. 1
1
Calculation constant to receive a warning of whether the chassis has an
Calculation constant to receive a warning of whether the chassis has an
unpermitted HIGH voltage depending on too low resistance between the
unpermitted HIGH voltage depending on too low resistance between the
chassis and the battery's positive pole. See table. Default is 917.
chassis and the battery's positive pole. See table. Default is 917.
Chassis const.2
Chassis const.2
Calculation constant to receive a warning of whether the chassis has an
Calculation constant to receive a warning of whether the chassis has an
unpermitted LOW voltage depending on too low resistance between the
unpermitted LOW voltage depending on too low resistance between the
chassis and the battery's negative pole. See table. Default is 110.
chassis and the battery's negative pole. See table. Default is 110.
Low batt.
Low batt.
level:
level:
Determines at what percentage of the battery capacity that the ATC shall
Determines at what percentage of the battery capacity that the ATC shall
warn that it is time to charge the battery. Default is 25%.
warn that it is time to charge the battery. Default is 25%.
Lift stop level
Lift stop level
Determines at what percentage of the battery capacity that the ATC
Determines at what percentage of the battery capacity that the ATC
should shutdown the lift function and limit the driving speed to crawling
should shutdown the lift function and limit the driving speed to crawling
speed. Default is 20%.
speed. Default is 20%.
https://www.besttruckmanuals.com/
