Asus AAM6020BI-T4 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 38

background image

AAM6030BI User Manual

Figure 17 (Static Routing)

The apply button will temporarily save this connection. To make the change permanent you need to click
on

Tools

(at the top of the page) and select

System Commands

. At the system commands page, click on

Save All

.

4.6.9

Dynamic Routing

Dynamic Routing allows the CPE to automatically adjust to physical changes in the network. The CPE,
using the RIP protocol, determines the network packets’ route based on the fewest number of hops between
the source and the destination. The RIP protocol regularly broadcasts routing information to other routers
on the network.

The Direction determines the direction that RIP routes will be updated.  Selecting In means that the CPE
will only incorporate received RIP information. Selecting Out means that the CPE will only send out RIP
information. Selecting both means that the CPE will incorporate received RIP information and send out
updated RIP information.

The protocol is dependent upon the entire network. Most networks support Rip v1. If RIP v1 is selected,
routing data will be sent in RIP v1 format. If Rip V2 is selected, routing data will be sent in RIP v2 format
using subnet broadcasting. If Rip V1 Compatible is selected, routing data will be sent in RIP v2 format
using multicasting.

To enable Dynamic Routing, from the Home screen, click Advanced and under Advanced, select Dynamic
Routing. Figure 18 illustrates a typical Dynamic Route.

30

30

«
...
28
29
30
31
32
...
»

Содержание AAM6020BI-T4







































Отзывы:

Нет отзывов

Похожие инструкции для AAM6020BI-T4

Бренд: 4IPNET Страницы: 97

Бренд: SAF Страницы: 30

Бренд: TC Electronic Страницы: 174

RouterBOARD SXT 5HnD

Бренд: MikroTik Страницы: 2

Бренд: Google Страницы: 14

Fast SwitchHub-8mi SNMP

Бренд: Accton Technology Страницы: 13

Бренд: INNOSILICON Страницы: 11

AceroDURO 100/S100

Бренд: CNC-Step Страницы: 86

BiPAC 5200S RC Series

Бренд: Billion Страницы: 79

Бренд: FOR-A Страницы: 37

Бренд: Paradyne Страницы: 28

Бренд: PACOM Страницы: 16

Business in a Box BIB NextGen

Бренд: AT&T Страницы: 9

Бренд: Costar Страницы: 14

Бренд: Crestron Страницы: 32

Бренд: Honeywell Страницы: 20

Бренд: Honeywell Страницы: 8

Бренд: Honeywell Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды