Honeywell CP-645 Скачать руководство пользователя

Страница: 1 / 20

INSTALLATION INSTRUCTIONS

Put Bar Code Here

62-0432-01

WEB-645, CP-645

Network Controller

ABOUT THIS GUIDE

This document covers the installation instructions of the Honeywell WEB-645 and CP-645 controllers. It assumes that you are an

engineer, technician, or service person who has performed control system installations. Instructions in this document apply to the

following products:

For complete specifications, please refer to the product data sheet for the WEB-645-AX and CP-645-AX controller.

NOTE: Not covered in this document is the WEB-AX-R2 or WEB-AX software installation and configuration required for

a fully functioning unit. See the “Related Documentation” section below. The content of this documentation

equally applies to CP-645-AX product.

Related Documentation

For software details on configuring and using the WEB-645-AX controller, consult the following documents:

•

Retrofit Board WEBs R2 Install & Startup Guide

(if WEBs R2)

•

JACE WEBs-AX Install and Startup Guide

(if WEBs-AX)

•

JACE Data Recovery Service (SRAM Support) - Engineering Notes

(if WEBs-AX)

Model

Description

Ports/Notes

WEB-645-AX

WEB-645I-AX

CP-645-AX

CP-645I-AX

JACE controller with various communication ports, mounted in a

metal enclosure. Has a pre-wired power transformer and

rechargeable 12V backup battery. (WEB-645-AX, CP-645-AX are for

U.S. installations, WEB-645I-AX, CP-645I-AX are for International

installations).

Controller uses an NPM6E processor module with a PowerPC

440EP CPU, 256MB DDR RAM, 128MB Serial Flash, 512KB Boot

Flash, 512KB Static RAM (SRAM), and runs the QNX Real-time

Operating System, and the Oracle Hotspot Java Virtual Machine.

Can host either a WEB R2 station (WEBs 2.301.535 or later) or a

WEB-AX station (WEB-AX 3.6.49 or later) for WEB products and CP-

AX Station (CP-AX 3.6.49 or later) for CP products, depending on

license.

Regardless of release, WEBs host (platform) configuration requires

WEB-AX Workbench 3.6.49 or later. If hosting an R2 station, the

existing R2 WEB Java Desktop Environment (JDE), build 2.301.535

or later, is used to access the controller’s running station.

2 -Ethernet 10/100 Mbit/s ports

(RJ-45 connectors).

4 - RS-485 ports, optically isolated, 3-

position connectors.

1 - LonWorks FTT-10A port, 2-position

connector.

2 - RS-232 port (RJ-45 connectors).

The LON port and all RS-485 ports

use pluggable screw terminal

connectors.

Содержание CP-645





















Результаты поиска

Содержание CP-645

Отзывы:

Похожие инструкции для CP-645

Бренды по названию

Популярные бренды

Honeywell CP-645, Руководство по установке

Результаты поиска

Содержание CP-645

Отзывы:

Похожие инструкции для CP-645

Бренды по названию

Популярные бренды