Honeywell CP-645 Скачать руководство пользователя

Страница: 10 / 20

WEB-645, CP-645 NETWORK CONTROLLER

62-0432—01

About the Battery

The WEB-645-AX controller is provided with a sealed lead-acid 12V battery. If battery trouble messages are generated upon

power up, contact Systems Engineering for technical support.

NOTE: As shipped, the backup battery in a new controller

not

fully charged. Allow 24 hours of powered operation

before relying on the battery to preserve station data on loss of power.

For more information on the use and replacement of the battery, refer to the “Required Battery Maintenance” section on page 13.

Commissioning Notes

To commission the controller, open a Workbench AX-3.6.49 or later host (platform) connection to the controller. You can do this

using an Ethernet patch cable between your Workbench PC and the LAN1 (primary) port on the NPM6E processor module,

where the factory default IP address for the LAN1 port is:

192.168.1.12

where

is the last numeral of the controller’s serial number

and the default subnet mask is

255.255.255.0

Then in the commissioning process, you reassign IP parameters as needed.

Or, first you can move a jumper on the NPM6E module to put the controller in “serial shell mode”. Then after rebooting it, you can

communicate using an RS-232 connection between your PC and the RS-232 COM1 port on the controller’s base board. This lets

you use “system shell” to reassign its IP parameters

before

starting the commissioning process from Workbench. See “Serial

Shell mode” on page 11.

See “Related Documentation,” page 1, for documents that cover JACE WEBs installation and startup.

CONTROLLER LEDS

The WEB-645-AX controller provides a number of LEDs,

including the following:

• LEDs on NPM6E processor module - Ethernet, Heartbeat,

Status

• LEDs on main circuit board - LON and serial (RS-485 and

RS-232) ports

LEDs on NPM6E processor module

shows the LEDs on the NPM6E processor module, with

descriptions

below.

Fig. 3. LEDs and serial shell jumper positions on NPM6E

processor module.

Ethernet

Each 10/100Mb Ethernet port, “LAN2” (Secondary) and

“LAN1” (Primary) has one green LED on the NPM6E module.

LED activity for an Ethernet port is as follows:

• Off—No Ethernet link is made

• On—Ethernet link is present, but no activity on the LAN

• Blinking—Ethernet link is present with data activity on the

LAN.

NOTE: The LAN2 (Secondary) Ethernet port in not sup-

ported in WEBs R2.

BEAT

(Heartbeat) In normal operation, the yellow “BEAT” LED

should blink about once per second. If the heartbeat LED

stays on constantly, does not light, or blinks very fast (more

than once per second), contact System Engineering for

technical support.

STATUS

The “STATUS” LED provides a CPU machine status check,

and should remain lit whenever the WEB Controller is

powered. If the STATUS LED does not light while power is

applied, contact System Engineering for technical support.

LAN2 (SEC)

LAN1 (PRI)

BEAT

STATUS

LAN1

(PRI)

LAN2

(SEC)

Содержание CP-645





















Результаты поиска

Содержание CP-645

Отзывы:

Похожие инструкции для CP-645

Бренды по названию

Популярные бренды

Honeywell CP-645, Руководство по установке

Результаты поиска

Содержание CP-645

Отзывы:

Похожие инструкции для CP-645

Бренды по названию

Популярные бренды