Honeywell CP-645 Скачать руководство пользователя

Страница: 3 / 20

WEB-645, CP-645 NETWORK CONTROLLER

62-0432—01

Static Discharge Precautions

Static charges produce voltages high enough to damage electronic components. The JACE printed circuit board contains

components that are sensitive to static discharge. Follow these precautions when installing or servicing the system:

CAUTION

• Work in a static-free area.

• Discharge any static electricity you may have accumulated. Discharge static electricity by touching a known, securely

grounded object.

• Do not handle printed circuit boards (PCBs) without proper protection against static discharge. Use a wrist strap when

handling PCBs. The wrist strap clamp must be secured to earth ground.

WEEE (Waste of Electrical and Electronic Equipment)

Recycling of Electronic Products: (International Installations)

In 2006 the European Union adopted regulations (WEEE) for the collection and recycling of all waste electrical and electronic

equipment. It is no longer allowable to simply throw away such equipment. Instead, these products must enter the recycling

process. To properly dispose of this product, please take it to a local recycling center.

If a local recycling center cannot be found, please return it to one of these offices:

MOUNTING

Mount the controller in a location that allows clearance for wiring, servicing, and module removal. For mounting details refer to

Fig. 1. on page 4 (a drill template is provided on the last page of this document).

Pay attention to the following recommendations and precautions when mounting and installing the unit.

• This product is intended for indoor use only. The unit should not be exposed to ambient conditions outside of the range of 0ºC

(32º F) to 50ºC (122º F) and relative humidity outside the range 5% to 95% non-condensing (pollution degree 1).

If the controller is mounted inside an enclosure, that enclosure should be designed to keep the unit within its required operating

range considering a 20-watt dissipation by the controller. This is especially important if the controller is mounted inside an

enclosure with other heat producing equipment.

• Minimum clearance from the wall on which the unit is mounted is 0.2-inches (provided by the dimpled mounting feet). Ensure

that this space is not compromised and that airflow is not blocked behind the unit.

• Do not mount the unit:

— in an area where excessive moisture, corrosive fumes, or explosive vapors are present.

— where vibration or shock is likely to occur.

— in a location subject to electrical noise. This includes the proximity of large electrical contractors, electrical machinery, welding

equipment, and spark igniters.

• The unit is designed to be wall mounted with the battery situated towards the bottom of the unit. For proper airflow at

temperature extremes, do not mount the unit oriented in any other way.

Tridium Europe Ltd

1, The Grainstore

Brooks Green Road

Coolham, West Sussex

RH13 8GR United Kingdom

Tridium Asia Pacific Pte Ltd

17 Changi Business Park Central 1

Honeywell Building

Singapore 486073

Tridium, Inc.

2256 Dabney Road, Suite C

Richmond, VA 23230

Содержание CP-645





















Результаты поиска

Содержание CP-645

Отзывы:

Похожие инструкции для CP-645

Бренды по названию

Популярные бренды

Honeywell CP-645, Руководство по установке

Результаты поиска

Содержание CP-645

Отзывы:

Похожие инструкции для CP-645

Бренды по названию

Популярные бренды