Asus AAM6020BI-T4 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 38

background image

AAM6030BI User Manual

Figure 20 (Ping test)

4.7.6

Modem Test

The Modem Test is used to check whether your Modem is properly connected to the WAN Network. This
test may take a few seconds to complete. To perform the test, select your connection from the list and press
the Test button. Before running this test, make sure you have a valid DSL link; if the DSL link is not
connected, this test will always fail.

Also the DSLAM must support this feature; not all DSLAMs have F4 and F5 support.

4.8

Status

The Status section allows you to view the Status/Statistics of different connections and interfaces

4.8.1

Network Statistics

Select to view the Statistics of different interfaces - Ethernet/USB/DSL.

4.8.2

Connection Status

Select to view the Status of different connections.

4.8.3

DHCP Clients

Select to view the list of DHCP clients.

4.8.4

Modem Status

Select to view the Status and Statistics of your broadband (DSL) connection.

4.8.5

Product Information

You can display the CPE’s driver and run-time information by going to the

Hom

e screen, under the

Status

title, click Product Information.

34

34

«
...
32
33
34
35
36
...
»

Содержание AAM6020BI-T4







































Отзывы:

Нет отзывов

Похожие инструкции для AAM6020BI-T4

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 2

Бренд: GE Страницы: 6

Бренд: JCG Страницы: 3

PG-FlexPlus AMU-912

Бренд: ADC Страницы: 130

totalstorage 200

Бренд: IBM Страницы: 180

Бренд: 8level Страницы: 52

Бренд: Perle Страницы: 491

Бренд: Connectland Страницы: 10

Бренд: KYLAND Technology Страницы: 19

Бренд: EMC Страницы: 88

Бренд: ZyXEL Communications Страницы: 191

Бренд: LevelOne Страницы: 4

Бренд: Goonas Страницы: 13

Бренд: Billion Страницы: 14

Бренд: LAWO Страницы: 68

Y.FORCE YTPC400

Бренд: YTTEK Страницы: 26

Бренд: Johnson Controls Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды