Assa Abloy Yale eBoss 886F Series Скачать руководство пользователя

Страница: 4 / 12

An ASSA ABLOY Group brand

80-8420-0900 Rev. B (05-08)

I-B

. Locate and Drill Holes for Electronic Components.

1. Mark door and position templates (Included).

a. Align the template with the 2-1/8" (54mm) hole using the

vertical and horizontal center lines.

b. Mark the remaining hole locations on both sides of the door.

c. Starting with the door face drill ½ way into the door

d Repeat drilling on the back face of the door.

e. Use the supplied Trim Blank (60-7000-7170) and screws

to cover the cylindrical latch bolt prep (if reqd).

Note: If a metal door is used, ensure it is of good quality

and has the proper reinforcements installed. This
will insure proper lock function.

SECTION

Prepare Lock for Installation

If the lock body is not correct hand, See Section

on Page 5

IIA

IIB

What is the hand of the door?

Face the door from the outside to determine its hand. The outside is the keypad side of an entrance door or the
corridor side of a room door.

INSTALLATION

TEMPLATE

HORIZONTAL
CENTERLINE

VERTICAL CENTERLINE

TAPE TO DOOR

Right Hand
Reverse:

Hinges on
right, opens
outward. For
handed
locks, specify
RHR.

Left Hand
Reverse:

Hinges on
left, opens
outward. For
handed
locks, specify
LHR.

Содержание Yale eBoss 886F Series













Результаты поиска

Содержание Yale eBoss 886F Series

Отзывы:

Похожие инструкции для Yale eBoss 886F Series

Бренды по названию

Популярные бренды

Assa Abloy Yale eBoss 886F Series, Руководство по установке

Результаты поиска

Содержание Yale eBoss 886F Series

Отзывы:

Похожие инструкции для Yale eBoss 886F Series

Бренды по названию

Популярные бренды