Assa Abloy ePED 1386-00 Скачать руководство пользователя

Страница: 54 / 64

Set-up operation

Initial commissioning

All devices are connected to the

Hi-O Technology

™ for the initial commissioning,

but are not conﬁgured yet. If the voltage supply is switched on, the system is in
plug and play mode and the devices work with the factory settings.

Interfaces for locking systems

cannot work with factory settings, because they must

be logically linked to the corresponding Emergency Open push-buttons. The
conﬁguration must be completely ﬁnished before the

Interfaces for locking systems

can be commissioned.

Any changes which are made necessitate re-conﬁguration
(

D01104xx ePED

Service Software Manual

Commissioning

Note!

Set-up:

All Hi-O devices must be connected to the bus for the conﬁguration. Then

the operating voltage is switched on. Subsequently connected devices are only
recognised after renewed connection of the operating voltage.

At least one Emergency Open module is always necessary for operation of the
RWT locking module.

1 Configure the system via the

ePED

Service Software

(

D01104xx ePED

Service Software

Manual).

Interface for

locking systems

Содержание ePED 1386-00

































































Результаты поиска

Содержание ePED 1386-00

Отзывы:

Похожие инструкции для ePED 1386-00

Бренды по названию

Популярные бренды

Assa Abloy ePED 1386-00, Инструкции по установке и монтажу

Результаты поиска

Содержание ePED 1386-00

Отзывы:

Похожие инструкции для ePED 1386-00

Бренды по названию

Популярные бренды