manualshive.com logo in svg

Aspect BIS VISTA, Руководство по эксплуатации

Поделиться
Скачать
Aspect BIS VISTA Скачать руководство пользователя страница 52

SECTION 7                               DIAGNOSTICS AND TROUBLESHOOTING 
________________________________________________________________________ 

 

 

 7-4  

 

 

 

 

 

7.3

 

BIS VISTA System Messages and Corrective 
Actions 

When an alarm is triggered, a message appears in the Message Region of the screen. Possible 
messages and the recommended operator actions are listed below: 
 

BIS VISTA Messages and Operator Actions 

 

Status Messages:  Causes: 

Corrective Actions: 

01 
Connect BISx 

1.

 

BISx disconnected. 

2.

 

Defective BISx cable. 

3.

 

Defective BISx. 

4.

 

Defective monitor. 

1.

 

Connect BISx. Verify all 
cable connections. 

2.

 

Replace Monitor Interface 
Cable. 

3.

 

Replace the BISx. 

4.

 

Replace monitor. 

 

13 
Re-prep Sensor 

1.

 

Incorrect sensor 
application. 

2.

 

Poor sensor 
connections. 

3.

 

Sensor Check fails 

4.

 

Defective PIC. 

5.

 

Defective BISx. 

1.

 

Read Instructions on 
sensor package and re-prep 
sensor. 

2.

 

Check sensor connections.  

3.

 

Re-prep again or replace 
sensor.  Verify Sensor 
Check passes.   

4.

 

Replace the PIC. 

5.

 

Replace BISx Bulkhead 
Connector or replace BISx. 

 

14 
Sensor Disconnected 

1.

 

Disconnected sensor. 

2.

 

Poor or contaminated 
connection between 
sensor and PIC. 

3.

 

Disconnected PIC. 

4.

 

Defective PIC. 

5.

 

Defective BISx. 

 

1.

 

Connect the Sensor. 

2.

 

Connect/clean connection 
between sensor and PIC. 

3.

 

Connect the PIC.  

4.

 

Replace the PIC. 

5.

 

Replace BISx Bulkhead 
Connector or replace BISx. 

Содержание BIS VISTA































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды