manualshive.com logo in svg

Aspect BIS VISTA, Руководство по эксплуатации

Поделиться
Скачать
Aspect BIS VISTA Скачать руководство пользователя страница 51

SECTION 7                               DIAGNOSTICS AND TROUBLESHOOTING 
________________________________________________________________________ 

 

 

 7-3  

 

 

 

 

 

Problem Isolation Procedure:

 Use the following sequence to determine the most probable 

cable: 

1.

 

With no sensor connected, run DSC Self Test (see Section 7.2.2 “BISx Checkout 
Procedure): 

•

 

If test fails or will not start, or the BISx is not recognized, the Monitor cable is 
likely suspect. This failure may also be related to a PCB problem in the BISx in 
which case the BISx must be replaced. 

•

 

If test indicates PASS, continue to step 2. 

 

2.

 

Connect Sensor Simulator or Test Simulator. Run Sensor Check (see Section 7.2.3 
“PIC Chekcout Procedure) 

•

 

If failure is noted, swap PIC with known good PIC cable and run again.  

•

 

If failure repeats, the BISx or the BISx Bulkhead Connector is suspect. This 
failure may also be related to a PCB problem in the BISx in which case the BISx 
must be returned to Aspect for service. 

 

Содержание BIS VISTA































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды