manualshive.com logo in svg

Aseptico AEU-27A, Инструкция по эксплуатации и техническому обслуживанию, Страница: 27 / 36

Поделиться
Скачать
Aseptico AEU-27A Скачать руководство пользователя страница 27

25

The AEU-27A has the ability to load

software updates and enhance the

functionality of the system, should this be

desired. A card slot, labeled “Memory Card

Port”, is provided on the back of the unit

(see Figure 7). This Port accepts memory

cards, P/N: MC-27A, that are very similar

to those used in common consumer

devices. These cards, available from

Aseptico, enable a user to update software

or replace existing software that might

have been accidentally erased or

corrupted. Contact Aseptico for more

information on card usage and availability.

To reprogram an AEU-27A unit, follow the

Steps below: 

Programming Steps:

1

. Turn ‘Off’ the Main Power Switch on the

back panel.

2.

Grasp the right-hand end of the rubber

dust cover for the Memory Card Port and

pry open the cover to expose the card slot.

3.

Insert the new memory card in the slot with

label facing upward (card terminals should

face downward). Carefully and slowly press

card inward until a ‘click’ is felt, then

release card.

4.

Turn the Main Power Switch (on the back

panel) ‘On’.

5.

The AEU-27A Display will show the

following message:

• Press the RATIO key on the Control Panel.

6

. The Display will show the following message:

• Press the RATIO key on the Control Panel.

7.

The Display will show the following message: 

• A status bar will indicate the progress of

the programming.

8

. When the programming is complete, the

Display will show the following message:

• Press the card inward slightly, then

release it to eject it. When the card is

ejected, the AEU-27A System will reset

with normal power-up screen displayed.

9.

Remove the memory card and store it in a

safe place. Close the rubber dust cover on

the Memory Card Port.
In the event that the programming

procedure is interrupted, the unit will

display the following message:

Then:

Re-start the programming procedure from

Step #1 (Remember to turn main power

‘Off’ before reprogramming).

REPROGRAMMING THE UNIT

Fig. 7 - Programming Slot

Memory Card Detected.

Re-program?

(RATIO = YES, CAL = NO)

Series Will Be Erased!

Continue?

(RATIO = YES, CAL = NO)

Programming...

Programming Successful.

Eject Card.

Programming Failed.

Eject Card.

Console Software Error.

Re-program unit.

MEMORY

CARD

DUST

COVER

Содержание AEU-27A





































Отзывы:

Нет отзывов