manualshive.com logo in svg

Aseptico AEU-27A, Инструкция по эксплуатации и техническому обслуживанию, Страница: 13 / 36

Поделиться
Скачать
Aseptico AEU-27A Скачать руководство пользователя страница 13

prompt will display:

The unit will run for approximately 30

seconds, measuring the handpiece for an

accurate display of speed and torque

values. It is recommended to calibrate at

the beginning of each day and when

handpieces are changed.
If calibration is successful, the following

prompt will appear, then the unit will return

to the last settings used:

If calibration fails, the following prompt will

appear advising the user to check the

motor/handpiece for problems. Press the

CAL button to escape out of the test:

B. System Setup:

Pressing, holding, then releasing the

CAL/SETUP button will enable the

System’s Setup options menu. Refer to

the System Setup section, page 16 for

complete instructions.

4 SPEED Buttons

Allow user to select desired

speed (RPM) for

motor/handpiece.

Press the SPEED Selector

Up/Down buttons to adjust

speed. The unit will

automatically enter MANUAL

mode and display the new

RPM settings with the ratio and torque

settings (example only):

Note:

For speed accuracy, the Ratio

Selector must match the ratio of the

handpiece being used. 

Note:

Speed ranges are accurate when

the handpieces referenced on page 1 are

used with the supplied 30K motor. Speed

ranges are shown in Chart 2, page 10.

5 Forward/Reverse (FWD/REV)

Button:

Sets the rotational direction of

the motor/handpiece.

Press and release FWD/REV

button until the desired rotation is

indicated: the green LED illuminates when

forward rotation is selected; the amber

LED indicates reverse rotation. An audible

tone will also indicate when reverse

rotation is activated. This reverse audible

tone may be adjusted or turned off as

described in the Setup Options Section,

page 17.

6 Torque Adjustment Buttons: 

Allow the user to adjust torque limits in

Gram•Centimeter increments.

Press the TORQUE Selector

Up/Down buttons to adjust

torque. The unit will

automatically enter MANUAL

MODE and display the new

TORQUE settings with the

ratio and speed settings

(example only):

11

MANUAL MODE

16:1  1800 RPM     60 g-cm

Calibration Failed!

Check Motor and Retest.

Press “CAL” to Escape.

Calibration Successful!

Please Wait.

MANUAL MODE

16:1  1800 RPM     90 g-cm

Testing In Progress...

Please Wait.

Содержание AEU-27A





































Отзывы:

Нет отзывов