ascon KX6, Инструкция по эксплуатации

Страница: 16 / 28

Ascon Tecnologic - KX6 - ENGINEERING MANUAL -
PAG. 16
the new set point (e.g. SP2).
2.
When “SP1.2” is used, the [61] nSP parameter
must be equal to 2.
[76] diSP - Middle Display Management
Available: Always.
Range: nonE Display not used;
SPF Final set point;
SPo Operative set point;
AL1 Alarm 1 threshold;
AL2
Alarm 2 threshold;
Po
Power output
[77] di.CL - Display colour
Available: Always.
Range: 0 The display colour is used to show the actual
deviation (PV - SP);
1 Display red (fix);
2 Display green (fix);
3 Display orange (fix).
[78] AdE - Deviation for display colour management
Available:
When [77] di.CL = 0.
Range:
1... 9999 engineering units.
[79] diS.t - Display time out
Available: Always.
Range: oFF The display is ever ON;
0.1... 99.59 minutes and seconds.
Note:
This function allows to turn OFF the display when no
alarm is present and no action is made on the instrument.
When
diS.t
is different from
oFF
and no button is
pressed for more than the programmed time out, the
display goes OFF and only 4 segments of the less
significant digit are turned ON in sequence in order to
show that the instrument is working correctly.
If an alarm occurs or a button is pressed, the display
will come back to the normal operation.
[80] FiLd - Filter on the displayed value
Available:
Always.
Range:
oFF Filter disabled;
0.1... 20.0 engineering units.
Note:
This is a “window filter” related to the set point, it is ap-
plied to the displayed value only and has no effect on the
other functions of the instrument (control, alarms, etc.).
[81] dSPu - Status of the instrument at power up
Available: Always.
Range: AS.Pr Starts in the same way it was prior to the
power down;
Auto Starts in Auto mode;
oP.0
Starts in manual mode with a power output
equal to zero.
St.bY
Starts in stand-by mode
Note:
When you change the value of [82] oPr.E, the
instrument forces [83] oPEr parameter equal to Auto.
[82] oPr.E - Operative modes enabling
Available:
Always.
Range: ALL
All modes will be selectable by the next
parameter.
Au.oP
Auto and manual (oPLo) mode only will be
selectable by the next parameter;
Au.Sb Auto and Stand-by modes only will be se-
lectable by the next parameter.
Note: Manual changing the value of [82] oPr.E, the
instrument forces parameter [83] oPEr = Auto.
[83] oPEr - Operative mode selection
Available:
Always.
Range:
When [82] oPr.E = ALL:
Auto = Auto mode;
oPLo = Manual mode;
St.bY = Stand by mode.
When [82] oPr.E = Au.oP:
Auto = Auto mode;
oPLo = Manual mode.
When [82] oPr.E = Au.Sb:
Auto = Auto mode;
St.bY = Stand by mode.
] Ser group - Serial link parameter
[84] Add - Instrument address
Available: Always.
Range: oFF = Serial interface not used;
1... 254.
[85] bAud - Baud rate
Available: When [73] Add different from
oFF
.
Range: 1200 1200 baud;
2400 2400 baud;
9600 9600 baud;
19.2 19200 baud;
38.4 38400 baud.
[86] trSP - Selection of the value to be
retransmitted
(Master)
Available: When [72] Add different from
oFF
.
Range: nonE Retransmission not used (the instrument is
a slave);
rSP The instrument become a Master and it
retransmits the operative set point;
PErc The instrument become a Master and it
retransmits the power output.
Note:
For more details see [69] SP.rt (Remote set point type)
parameter.