background image

Ascon Tecnologic - KX6 - ENGINEERING MANUAL - 

PAG. 5

4  TECHNICAL CHARACTERISTICS

Case:

 Plastic, self-extinguishing degree: V-0 according to UL 94;

Front protection: 

IP65 (when the optional panel gasket is 

mounted) for indoor locations according to EN 60070-1;

Terminals protection:

 IP20 according to EN 60070-1;

Installation:

 Panel mounting;

Terminal block: 

24 M3 screw terminals for cables of 

0.25... 2.5 mm

2

 (AWG22... AWG14) with connection diagram;

Dimensions:

 48 x 96, depth 89,15 mm.

Panel cutout:

 45

(+0.6)

 x 89

(+0.6)

 mm [1.78

(+0.023)

 x 3.5

(+0.023)

 in.]

Weight: 

160 g max..

Power supply: 

 100... 240 VAC (-15... +10% of the nominal  

 

    value);

P

ower consumption:

 5 VA max.;

Insulation voltage:

 3000 V rms according to EN 61010-1;

Display updating time:

 500 ms;

Sampling time: 

130 ms;

Resolution:

 30000 counts;

Total Accuracy: 

±0.5% F.S.V. ±1 digit @ 25°C of room 

temperature;

Temperature drift:

 It is part of the global accuracy;

Operating temperature:

 0... 50°C (32... 122°F);

Storage temperature:

 -30... +70°C (-22... +158°F);

Humidity:

 20... 85% RH, not condensing.

Electromagnetic compatibility and safety requirements

Compliance:

• 

EMC Directive (EN 61326-1),

• 

Safety Directive (EN 61010-1);

Installation category:

 II;

Pollution category:

 2.

5  HOW TO ORDER

Power supply

H

 = 100... 240 VAC

Analogue input + digital input DI1

 (standard)

B

 = J, K, R, S, T, mA, mV (*)

Output 3

R

 = Relay SPST NO 2 A (resistive load)

Output 4

R

 = Relay SPST NO 2 A (resistive load)

Options 

(the TTL Modbus port is always present)

-

  = Not available

C

 = Potentiometer input + Digital Input 2 + RS 485 Modbus

P

 = Potentiometer input + Digital Input 2

S

 = RS 485 Modbus

Model

KX6

 - =  Valve Controller

Output 1 + Output 2

I-

  =  Output 1: 0/4... 20 mA, 0/2... 10 V; Output 2: Not available

MM

 =  Output 1 + Output 2: Relays for servomotor SPST NO 2 A

KX6- H B

R R

It is possible to obtain a 0... 10 V or 0... 5 V input, 
ordering the following part no., respectively:

• 

 AP ADPINMV-KX-V10 (for 0... 10 V);

• 

 AD ADPINMV-KX-V5 (for 0... 5 V).

Содержание KX6





























Отзывы: