manualshive.com logo in svg

Art Hobby Momentum 1500mm SAL DLG F3K, Руководство пользователя

Поделиться
Скачать
Art Hobby Momentum 1500mm SAL DLG F3K Скачать руководство пользователя страница 8

12. Rotate plug face UP then use CA and glue thin planks to the 
connector walls - boxing it around. Photo 36

P. 36

13. Now pulling gently both servo wires and push boxed connector 
into center opening. If satisfied with fitment mix small amount of 5 
min. epoxy and glue connector flush into joint. Photo 37
14. Use two 12” servo extensions and 4-pin male connector for 
making plug type 

wing to receiver

 wiring harness. Photo 37

P. 37

15. Wires  and 4-pin male connector with shortened soldering pins 
prepared for soldering Photo 38.

16. Solder wires to 4-pin male connector in exactly same order 
and polarity as you solder servo wires to 4-pin female connector 
glued into wing center joint.
During  soldering  align  wires  long  ways  to  make  nice  slim 
connector plug. 
After soldering wires wrap plug and wires with   sewing threads   
securing it with CA - this will make strong plug connector   that 
could be plugged and unplugged from wing hundreds of times with 
out damaging. Photo 39 & 40

P. 38

P. 39

17. Now  plug harness to the wing and connect to corresponding 
aileron channels in the receiver. Turn ON the radio then power 
receiver -  test servos proper movement, direction and set them to 
neutral position. Photo 41

P. 40

P. 41

Aileron Servo and Control Horn Installation

Note:  Aileron  control  horns  are  installed  on  the  aileron 
bottom  surface  with  the  horn  posts  projecting  from  top 
surface of the aileron.

1. Check  aileron servo for proper positioning in servo bays.
2.  Use  angle  ruler  and  position  it  perpendicular  to  the  aileron 
trailing edge pressing ruler edge to the servo horn. If satisfied with 
alignment draw light pencil line on the aileron surface. Photo 42 

Momentum-DL v.1

8

Содержание Momentum 1500mm SAL DLG F3K


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды