manualshive.com logo in svg

Art Hobby Momentum 1500mm SAL DLG F3K, Руководство пользователя

Поделиться
Скачать
Art Hobby Momentum 1500mm SAL DLG F3K Скачать руководство пользователя страница 5

Recommended tools for cutting ailerons:
- 

Two pins.

 will be used to project aileron inner corners/outlines 

to the wing bottom sheeting.  Photo 17, 18 & 19
-  

Triangle shaped Needle File

 (diamond) for finishing surfaces 

after cuts. Photo 17
-  

Hobby knife with blade #11

. Phot 17

(blade tip sanded round ~1mm radius and dull will be used to 
make long cuts (top and bottom) over the aileron hinge. 
Rounded tip blade will cut veneer and balsa strip molded inside 
the wing but will prevent from cutting embedded hinge tape
- 

Balsa saw

 #A0530 (or saw blade #A0539)   for making short 

precision cuts on both sides of the ailerons cutting top and bottom 
veneer sheeting. Photo 20 & 21

9. After epoxy cures remove masking tape.
10. Using sanding block with 320 - 400 grid sand paper sand 
both servo boxes flush with the wing surface.  Photo 16

P. 16

1. Use pins to project aileron inner corners/outlines to the wing 
bottom sheeting. Photo 18
2. Place wing panel bottom side Up and draw a line connecting 
both pins. Photo 19

P. 17

3. Remove pins and using balsa saw make short precision cuts on 
both sides of the ailerons cutting top and bottom veneer sheeting. 
Photo 20 & 21

P. 18

P. 19

P. 20

P. 21

Wing Control Surfaces

Refer to glider drawing and check ailerons and flaps pencil 
marked on the wing.

 

There is a thin ARAMID hinge tape molded 

under wing upper skins where the aileron are. Fig.1

Fig. 1

Momentum-DL v.1

5

Aramid hinge for the ailerons is
laminated under bottom wing skin

Balsa strip inside wing

Содержание Momentum 1500mm SAL DLG F3K


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды